Millwork, stair and trim glossary
The trade has a precise vocabulary and very little accurate reference for it. These are the 159 terms that come up in stair, moulding and trim work, defined at the level the work is actually done — what the part is, what governs it, and what goes wrong when it is got wrong.
Stairs
35 termsThe parts of a staircase and the geometry that governs them.
- BalusterOne of the vertical members filling the space between a handrail and the treads or floor.
- Bending railA handrail supplied as thin laminations so it can be glued and clamped around a curve on site or in the shop.
- Closed stringerA stringer with treads and risers housed into routed pockets, reading as one clean sloped board.
- EasingA curved handrail fitting that changes the rail from one angle to another without a visible joint.
- FilletA short strip that fills the plow between balusters in a plowed rail or shoe rail.
- GooseneckA handrail fitting that lifts the rail vertically at a landing before turning it back to level or into a new rake.
- GraspabilityWhether a handrail profile can actually be gripped, defined by code as one of two types.
- GuardThe barrier at an open edge that stops a person falling — a different requirement from a handrail.
- HandrailThe rail a hand actually holds while using a stair, as distinct from a guard.
- HeadroomThe clear vertical height above the walking line of a stair, measured from the nosings.
- LandingA flat platform where a stair changes direction, or pauses between flights.
- Landing treadA narrow hardwood strip with a finished front edge that closes the floor at the top of a stair.
- Mitred returnA short mitred piece that carries the nosing profile around the exposed end of a tread.
- NewelThe heavy post that anchors a handrail at a start, a turn, or a landing.
- Newel capThe finished top of a newel post, either turned as part of the post or applied as a separate piece.
- NosingThe front edge of a stair tread, where it projects out past the face of the riser below.
- Open stringerA stringer sawn to the sawtooth profile of the steps, leaving the end of each tread visible.
- Over-the-postA balustrade in which the handrail runs continuously over the tops of the newels using fittings.
- Plowed railA handrail with a groove machined into its underside to receive square balusters and fillet.
- Post-to-postA balustrade in which the handrail runs in separate lengths between full-height newels.
- Retro-fit treadA thinner tread made to cap an existing stair in place, without tearing the old one out.
- RiseThe vertical height from the top of one tread to the top of the next, finish to finish.
- RiserThe vertical board that closes the space between one tread and the next.
- RosetteA small wall plate that receives the end of a handrail where it dies into a wall.
- RunThe horizontal depth of one step, measured from the face of one riser to the face of the next.
- Shoe railA plowed rail at the bottom of a balustrade that receives the feet of the balusters.
- Skirt boardThe finish board run against the wall alongside a stair, following its slope.
- Starting stepThe first step of a stair, made wider than the rest and usually rounded at one or both ends.
- StringerThe sloped structural member running the length of a stair that carries the treads and risers.
- Total riseThe full vertical distance a stair climbs, from finished floor to finished floor.
- Total runThe full horizontal distance a stair occupies, from the first riser face to the last.
- TreadThe horizontal surface of a step — the part underfoot, and the part that wears.
- Tread bracketA decorative applique fixed to the face of an open stringer beneath the end of each tread.
- VoluteThe curled, spiral fitting that terminates a handrail over a starting step.
- WinderA tapered tread that turns a stair through an angle instead of using a landing.
Moulding & trim
45 termsProfiles, where each one runs, and the joinery that installs it.
- ApronThe trim run horizontally under a window stool, closing the wall beneath the sill.
- Back bandA small moulding run around the outside edge of flat casing to add depth and a finished edge.
- Back reliefShallow channels machined into the unseen back of a moulding so it sits flat against an uneven wall.
- Base shoeA small moulding run at the foot of a baseboard to close the gap at the floor.
- BaseboardThe moulding run along the bottom of a wall, closing the joint where it meets the floor.
- BattenA narrow strip applied over the joint between two boards, covering it while letting both move.
- BeadboardNarrow vertical boards with a bead along each joint, used as a wall or ceiling surface.
- Bed mouldA small sprung moulding used at a wall and ceiling junction or as part of a built-up cornice.
- Board and battenA wall treatment of wide flat boards with narrow battens covering the joints between them.
- Brick mouldExterior casing nailed to the jamb of a door or window for the masonry or siding to stop against.
- BullnoseA fully rounded edge, struck as a half-circle across the thickness of the piece.
- CasingThe trim run around a door or window opening, covering the joint between jamb and wall.
- Chair railA horizontal moulding run around a room at roughly the height of a chair back.
- CopeAn inside-corner joint where one piece is cut to the profile of the other and fits over it.
- Corner mouldA moulding run at the meeting of two panelled faces, covering the joint instead of mitring it.
- Cove mouldingA moulding with a simple concave face, used at wall and ceiling junctions or as a component of a build-up.
- Crown mouldingA moulding installed at the junction of wall and ceiling, sprung at an angle between the two.
- Door stopThe thin strip fixed to a door jamb that the door closes against, hiding the gap at the edge when it is shut.
- Drip capThe sloped exterior moulding over the head of a window or door that throws water clear of the joint below.
- Full roundA moulding turned or milled round through its whole section — a dowel sold as lineal stock.
- Half roundA moulding whose section is a half circle, flat on the back so it lies against the surface it trims.
- LatticeThe thinnest flat stock a mill runs — roughly 1/4″ to 5/16″ thick, an inch or two wide, edges eased.
- LinealMaterial sold by the length rather than by area or by the piece, and taken off that way too.
- Lip mouldA small rabbeted profile that finishes an exposed edge — a counter, a shelf or a cabinet face.
- Mantle mouldThe heavy edge profile that finishes the front of a mantel shelf or a bar top.
- MitreA joint where two pieces are each cut at half the corner angle so the profile continues around it.
- Overlap reducerA transition moulding that ramps down from a thicker floor to a thinner adjacent surface.
- Panel mouldA small moulding used to form the frames of applied wall panels, fixed directly to the wall.
- Picture mouldA moulding run high on the wall with a rounded top edge, made for hanging pictures from hooks rather than nails.
- ProfileThe shape of a moulding seen end-on — the single thing that identifies it.
- Quarter roundA moulding whose section is a quarter of a circle, used where a base shoe would be.
- RabbetA stepped recess cut along the edge of a piece, open on two faces rather than enclosed.
- RevealThe narrow setback of casing from the face of a jamb, left deliberately rather than running flush.
- S3SStock surfaced on three sides, with one edge left rough for the installer to rip.
- S4SStock surfaced on all four faces to a finished dimension, with no profile run on it.
- Screen mouldA narrow flat-backed moulding that covers the stapled edge of screening or the seam between two panels.
- ScribeCutting a piece to follow the irregular line of an adjacent surface rather than to a straight edge.
- ShiplapBoards with a rabbet along each edge so they overlap and leave a consistent gap between faces.
- Spring angleThe angle at which a crown moulding sits between wall and ceiling, which sets every saw angle used on it.
- Stair nosing mouldingA lineal moulding that finishes the edge of a floor where it steps down, distinct from a stair tread.
- T-astragalThe T-section moulding fixed to one leaf of a pair of doors, covering the gap where the two meet.
- ThresholdA shaped piece closing the joint between two floor finishes at a doorway.
- Tongue and grooveBoards machined with a projecting tongue on one edge and a matching groove on the other.
- WainscotingA treatment applied to the lower part of a wall, distinct from the finish above it.
- Window stoolThe interior sill of a window — the horizontal board the side casings land on and the apron hangs beneath.
Wood & material
25 termsHow wood behaves, and the terms used to describe and grade it.
- AcclimationLetting material reach the moisture content of the space before it is installed.
- CheckingSplits that open along the grain when a surface dries and shrinks faster than the wood beneath it.
- CuppingA board curving across its width, usually because its two faces are at different moisture contents.
- Edge grainA glued-up panel presenting the narrow edges of the boards as the working surface.
- Edge-gluedA wide piece made by gluing several narrower boards together edge to edge.
- End grainA panel built from short blocks stood on end so the cut ends of the fibres form the surface.
- Equilibrium moisture contentThe moisture content wood settles at when left in a given temperature and humidity.
- Face grainA panel presenting the wide face of the boards, showing the full figure of the species.
- FigureThe pattern visible on a wood surface, produced by how the grain was cut and by irregularities in growth.
- Finger-jointedShort lengths joined end to end with interlocking machined fingers to make a long piece.
- Flex mouldingA moulding cast in a flexible polymer to match a wood profile, for running around curves.
- GrainThe direction and texture of the wood fibres, and how they appear on a cut surface.
- HardwoodTimber from a broadleaf, deciduous tree — a botanical category, not a statement of hardness.
- Janka hardnessA measured resistance to denting, given in pounds-force, used to compare species.
- Kiln driedLumber dried under controlled heat and humidity to a target moisture content.
- MDFAn engineered panel of wood fibre and resin, dense and uniform, used for paint-grade profiles.
- Mill runMaterial taken as it comes off the run, without selection for colour or figure.
- Moisture contentThe weight of water in a piece of wood expressed as a percentage of its oven-dry weight.
- Plain sawnBoards cut tangentially to the growth rings, giving the familiar cathedral figure.
- PrimedSupplied with a factory undercoat, ready for finish paint after preparation.
- Quarter sawnBoards cut so the growth rings run roughly perpendicular to the face, giving a straight, striped grain.
- Rift sawnBoards cut at an angle between plain and quarter sawn, giving a tight linear grain with no flake.
- SoftwoodTimber from a coniferous tree — again a botanical category rather than a measure of hardness.
- TearoutFibres lifted and broken out of a surface by a cutter travelling against the grain.
- Wood movementThe dimensional change of wood as it gains or loses moisture, almost entirely across the grain.
Milling & fabrication
8 termsHow a profile gets made, drawn, and documented.
- DXFA vector CAD file format used to exchange a profile section between drawing and machining software.
- KnifeThe ground steel cutter that carries the reverse of a profile and cuts it into the stock.
- MoulderThe machine that shapes a moulding, feeding stock past several powered cutterheads at once.
- SetupThe work of getting a machine ready to run one particular profile, charged once regardless of footage.
- Shop drawingA dimensioned drawing of the part as it will actually be made, produced by the fabricator for approval.
- StickerA thin strip laid between layers of stacked lumber so air can reach every face.
- SubmittalThe package a supplier provides for approval before fabrication — drawings, data, and samples.
- TemplateA physical pattern taken from the actual opening, used to make a part that has no catalogue size.
Codes & standards
15 termsThe codes and industry standards millwork is specified against.
- ADACivil rights legislation whose design standards govern accessible routes in places of public accommodation.
- Architectural Woodwork StandardsThe industry standard defining grades and tolerances for architectural woodwork, in three levels of quality.
- ASTM E84The surface-burning test that assigns a flame-spread index and a smoke-developed index to a building material.
- AWIThe trade institute that co-publishes the Architectural Woodwork Standards and certifies fabricators to them.
- CARB Phase 2The California formaldehyde emission limit for composite wood panels, which became the national floor under TSCA Title VI.
- CSI MasterFormatThe numbering system that organises construction specifications into divisions and sections.
- Division 06The MasterFormat division covering wood, plastics and composites — where millwork is specified.
- IBCThe model code covering buildings outside the scope of the IRC, including commercial and multi-family work.
- ICC A117.1The technical accessibility standard building codes reference for accessible design.
- IRCThe model code covering one- and two-family dwellings, and the source of most residential stair rules.
- NFPA 253The radiant-panel test for floor coverings, which rates a flooring by the heat flux needed to keep it burning.
- NHLA gradeThe hardwood lumber grading rules that define FAS, Select and the Common grades by the yield of clear cuttings in a board.
- NWFAThe trade association whose installation and sand-and-finish guidelines are the reference for wood flooring work in North America.
- WM numberA part number from the industry standard moulding series, used across suppliers to identify a profile.
- WMMPAThe trade association that publishes the WM series of standard moulding profiles and the grading rules for finger-jointed and solid moulding.
Commercial & specification
31 termsEgress and fire, the specification process, and the compliance documents an institutional project asks for.
- Accessible routeA continuous unobstructed path connecting accessible spaces, with limits on slope and changes in level.
- AddendumA formal change to the bidding documents issued before bids are received.
- AllowanceA sum carried in the contract for work not yet defined, reconciled when the selection is made.
- AlternateA priced option the owner may accept or decline, bid alongside the base scope.
- Authority having jurisdictionThe official body that adopts, interprets and enforces the code on a given project.
- Basis of designThe specific product a specification is written around, named so others can be judged against it.
- Chain of custodyDocumented tracking of certified material from forest through every processor to the finished product.
- Change orderA signed amendment to the contract changing the scope, the price, or the schedule.
- Construction documentsThe drawings and specifications that define the work for permit, bidding and construction.
- Egress stairA stair that forms part of a building’s required exit system, and is regulated as such.
- Environmental product declarationA verified, standardised report of a product’s environmental impact across its life cycle.
- Exit enclosureThe fire-rated shaft around a required stair, separating it from the rest of the building.
- Field verificationMeasuring the actual conditions on site, before anything is fabricated to fit them.
- Flame spread indexA tested number describing how quickly flame travels across a surface, used to classify interior finishes.
- Guard loadThe force a guard and its anchorage must resist, specified as both a concentrated and a distributed load.
- Guide specificationA manufacturer-written specification section an architect edits into their project manual.
- Handrail extensionThe continuation of a handrail past the top and bottom of a flight, required on most commercial stairs.
- Health product declarationA standardised disclosure of the ingredients in a product and their associated health hazards.
- Interior finish classificationThe code’s grading of wall and ceiling finishes by how they behave in a fire, as Class A, B or C.
- LEEDA green building rating system whose credits reach millwork through material sourcing and emissions.
- Means of egressThe continuous, unobstructed path from any point in a building to a public way.
- Mock-upA full-size sample of finished work, built for approval before production begins.
- Occupancy classificationThe code’s category for what a building is used for, which drives most of its other requirements.
- Or-equalA clause permitting substitution of a product the architect judges equivalent to the one named.
- Performance specificationA specification that states the result required and leaves the means to the supplier.
- Prescriptive specificationA specification that states exactly what to provide — product, material, dimension and method.
- Punch listThe list of incomplete or defective items to be corrected before the work is accepted.
- Request for informationA formal question from the contractor to the design team about the documents.
- Substantial completionThe point at which the owner can occupy and use the work for its intended purpose.
- TSCA Title VIThe federal limit on formaldehyde emissions from composite wood panels sold in the United States.
- VOCCompounds that off-gas from finishes and adhesives, limited by regulation and by green building standards.

