Skip to main content
Unique Wood Products
A living room feature wall of horizontal white oak shiplap boards with a nickel-gap reveal, warm afternoon light raking across the wall
Crafted In-House · Service-Driven · Trade-Proven

Hardwood Shiplap

Milled to Order · Solid Hardwood · NW Houston / Tanner Rd

Rabbeted shiplap milled on our own floor in solid hardwood or paint-grade poplar. Flush or a 1/8", 1/4" or 1/2" reveal, any species and width — run to order for feature walls, ceilings and built-ins, and drawn below so you can read the joint before you order it.

Stock

1x6 · 3/4" × 5-1/2"

Reveal

Flush · 1/8" · 1/4" · 1/2"

Species

Six core · others by quote

Pickup

NW Houston / Tanner Rd

Solid, not veneer

Real hardwood boards with a milled rabbet on each edge — sand, stain and finish them like any solid wood. Not a thin MDF panel printed to look like shiplap.

Rabbeted, self-spacing

The 1/2" lap on opposite faces of opposite edges lets each board sit over the last and carry the reveal. The gap is a slot over solid wood, never daylight.

Milled to your run

Your species, face width, reveal and lengths — milled to order and laid out to minimise seams across the wall or ceiling. Quoted to order.

The profile

One rabbet, four reveals.

Every board below is a 3/4" × 5-1/2" 1x6 drawn in section, two boards at the joint, the way the knife is set: a 1/2" lap rabbeted to half the thickness on opposite faces of opposite edges. The reveal is the only thing that changes. Under each section, the same joint face-on across a run.

Close view of the joint between two unfinished white oak shiplap boards: the upper board lapping the lower with a quarter-inch reveal reading as a dark slot
The joint in wood: the lap under, the reveal reading as a shadow, the rabbet square off the knife. Unfinished white oak at a 1/4" reveal.
SUBSTRATE — STUDS, FURRING OR JOISTS3/4"1/2" lapflush — faces meet, no revealrabbet, half the thickness1x6 · 3/4" × 5-1/2" · 1/2" LAP · COVERAGE ≈ 5" PER BOARD
1x6 · 3/4" × 5-1/2" · 1/2" lap · flush · coverage ≈ 5"" per board

Flush

No reveal

Faces meet with no gap for a continuous surface — the traditional paint-grade wall, where the joint reads as a hairline once painted.

SUBSTRATE — STUDS, FURRING OR JOISTS3/4"1/2" lap1/8" revealrabbet, half the thickness1x6 · 3/4" × 5-1/2" · 1/2" LAP · COVERAGE ≈ 5-1/8" PER BOARD
1x6 · 3/4" × 5-1/2" · 1/2" lap · 1/8" reveal · coverage ≈ 5-1/8"" per board

1/8" reveal

Fine shadow line

A fine, even shadow between boards. Subtle enough for a whole room; crisp enough to read as boards rather than a flat wall.

SUBSTRATE — STUDS, FURRING OR JOISTS3/4"1/2" lap1/4" revealrabbet, half the thickness1x6 · 3/4" × 5-1/2" · 1/2" LAP · COVERAGE ≈ 5-1/4" PER BOARD
1x6 · 3/4" × 5-1/2" · 1/2" lap · 1/4" reveal · coverage ≈ 5-1/4"" per board

1/4" reveal

Nickel gap

The contemporary nickel-gap look — a clean, deliberate shadow line that carries across a feature wall or ceiling.

SUBSTRATE — STUDS, FURRING OR JOISTS3/4"1/2" lap1/2" revealrabbet, half the thickness1x6 · 3/4" × 5-1/2" · 1/2" LAP · COVERAGE ≈ 5-1/2" PER BOARD
1x6 · 3/4" × 5-1/2" · 1/2" lap · 1/2" reveal · coverage ≈ 5-1/2"" per board

1/2" reveal

Bold reveal

A deep, architectural reveal that reads strongly from across the room. Usually run horizontally on a large wall or a high ceiling.

Sections are drawn to proportion, not to scale on screen. Knives are ground in-house, so a deeper lap, a different reveal or a matched sample can be run against a section drawing.

Which board

Shiplap, tongue & groove, or board & batten.

Three boards get called “shiplap” on a finish schedule. They fit differently, fasten differently, and only one of them carries a reveal you choose. UWP mills all three; this is how to tell the counter which one you mean.

JointHow it fitsFasteningRevealBest for
ShiplapA rabbet on opposite faces of opposite edges; each board laps over the last.Through the back rabbet, hidden by the next course — or face-nailed and filled.Flush, 1/8", 1/4" or 1/2" — the lap carries whatever gap you choose.Feature walls, ceilings, mudrooms, built-in backs. The easiest board to fit and the one with the reveal as its feature.
Tongue & grooveA tongue on one edge seats in a groove on the other; the boards interlock.Blind-nailed through the tongue; no fastener shows and none needs filling.Set by the profile — V-groove, bead, nickel gap or square — not by a spacer.Ceilings and soffits, long spans, anywhere the boards must stay flat and the fastener must vanish.
Board & battenFlat boards butted or spaced, with a narrow batten covering each joint.Face-nailed board and batten; the batten hides the joint, not the nail.None — the batten is the feature, standing proud of the boards.Wainscot and exterior-style walls where a raised vertical rhythm is wanted.

Tongue & groove profiles are drawn on their own page: hardwood tongue & groove. Board & batten is quoted as S4S boards and battens from dimension stock.

Species and finish

Paint-grade to character hardwood.

Poplar keeps a painted wall quiet and lets the reveal do the work; the stain-grade hardwoods turn the same profile into a feature. Anything else is milled to order with timing on the quote.

Images simulate a water-clear matte coat to show natural species colour. Material ships unfinished; tone and figure vary by board.

Poplar representative hardwood grain under a clear matte finish.

Poplar

Paint-grade

Pale, tight, takes colour clean — the standard for painted walls and ceilings.

White Oak representative hardwood grain under a clear matte finish.

White Oak

Premium

Warm-tan with an olive cast; the modern feature-wall favourite, stained or clear.

Red Oak representative hardwood grain under a clear matte finish.

Red Oak

Standard

Warm reddish cast and bold, open grain for traditional rooms.

Maple representative hardwood grain under a clear matte finish.

Maple

Clean & pale

Even, fine grain that reads crisp and contemporary under a clear coat.

Walnut representative hardwood grain under a clear matte finish.

Walnut

Dark & refined

Rich chocolate-brown; a warm, high-end statement wall.

Hickory representative hardwood grain under a clear matte finish.

Hickory

High character

Strong grain and colour variation — rustic warmth, hard-wearing.

Freshly milled unfinished white oak shiplap boards stacked on a bench, seen from the end so the stepped rabbet on each edge reads
Off the moulder: the rabbet reads on the end of every board. Boards ship sanded and unfinished, in the species and width on the quote.
Paint-grade or stain-grade

The finish plan picks the species.

Painted wall or ceiling

Paint-grade Poplar. Tight, pale and stable under paint, with no open grain to telegraph through the coat. Prime every face before it goes up so the reveal never flashes bare wood, then two topcoats after fitting.

Stained or clear-coated

White Oak for the modern feature wall, Red Oak for traditional rooms, Walnut for a dark statement, Maple for a clean pale surface, Hickory for character. Seal all six faces; the reveal shows the edge of every board.

Colour matters more on shiplap than on a flat wall because the reveal shows the edge grain of every course. Stain-grade boards are selected for colour across the run; paint-grade boards are selected for a clean face. Say which on the quote and the yard pulls the right lumber.

Stock sizes & coverage

1x4 through 1x12.

1x6 is the standard board; 1x10 and 1x12 are subject to availability. Coverage is per course at a 1/4" reveal.

NominalActualCoverage
1 × 43/4" × 3-1/2"3-1/4"
1 × 63/4" × 5-1/2"5-1/4"
1 × 83/4" × 7-1/4"7"
1 × 103/4" × 9-1/2"9-1/4"
1 × 123/4" × 11-1/4"11"

All stock is 3/4" nominal thickness with a 1/2" lap. Coverage for a flush, 1/8" or 1/2" reveal is confirmed on the written quote, which also carries a 10–15% cut allowance. Custom thicknesses and widths milled on request.

Where it goes

Walls, ceilings and the millwork between.

The application changes the recommendation as much as the reveal does.

A living room feature wall of horizontal white oak shiplap with a nickel-gap reveal, a low walnut console in front of it
Feature walls

Horizontal or vertical runs behind a bed, a fireplace or a dining wall. A 1/4" reveal in White Oak or paint-grade Poplar is the usual starting point.

A bedroom ceiling of painted white shiplap boards running the length of the room under a linen pendant
Ceilings

Shiplap on a ceiling hides the seasonal movement in the joint and gives a long span rhythm. Narrower boards read finer overhead; 1x6 is the safe default.

An entry hall stair wall clad in vertical white oak shiplap beside an oak handrail and oak treads
Stair & entry walls

Shiplap that ties into matching UWP treads, handrail and trim so the entry reads as one hardwood program.

Mudrooms, halls & built-ins

Wainscot-height runs behind benches and hooks, cabinet ends and island backs — the same board and reveal carried through the millwork.

Covered porch ceilings

Protected exterior work only. Send the exposure and the finish schedule; species and back-priming are confirmed on the quote.

Hospitality & retail

Lobbies, restaurants and offices where the wall sets the room — trade runs milled to commercial footage with a known lead time.

For the installer

Six notes that keep a run flat and true.

UWP mills the boards; your carpenter fits them. These are the notes we send with every run. The full sequence — acclimation, fastening schedule and finishing — is on the quote.

  1. Acclimate 72 hours

    Stack the boards flat in the conditioned room for at least three days before fastening. Solid wood moves with the house; let it get there first.

  2. Fasten through the lap

    Nail through the back rabbet into framing or furring at 16" centres so the next board covers the fastener, or face-nail with a finish nail and fill. Do not glue the full face.

  3. Hold the reveal

    Use a spacer of the reveal size at every course. The rabbet is milled so the lap carries the gap; the spacer keeps the run true across the wall.

  4. Leave room at the ends

    Hold 1/8" at inside corners and at trim; the caulk or the corner board closes it. Long runs move most along their length.

  5. Horizontal from a level line

    Start the first course on a level line at the floor with the lap facing up, so each board sits over the last. Vertical runs need horizontal furring or blocking at 16–24" to nail into.

  6. Finish after fitting

    Boards ship unfinished and sanded. Paint-grade: prime the back and edges before install so the reveal does not flash bare wood. Stain-grade: seal all faces.

What to expect

Milled-to-order shiplap, stated plainly.

The things the counter gets asked before every run, answered here so the quote holds no surprises.

Grade and character

Solid hardwood varies board to board: colour, figure, mineral streak and the occasional tight knot are the material, not defects. Paint-grade Poplar is selected for a clean face under paint; stain-grade species are selected for colour and figure across the run, and a rift or quartered cut can be quoted for a quieter grain.

Lengths

Boards run in the lengths the lumber yields — random lengths across the run unless you specify fixed lengths, which are cut from longer stock and confirmed on the quote. Tell us the longest wall or ceiling span; we lay the run out to minimise seams.

Moisture and movement

Kiln-dried to 6–9% moisture content, the range a conditioned Houston interior settles into. Solid wood still moves across its width with the seasons; the joint is designed to hide it, and the 72-hour acclimation before install is what keeps it hidden.

Tolerances

Thickness ±1/32", face width ±1/16", the same tolerances UWP prints on its shop drawings. Profiles are milled from knives ground in-house; a matched sample or section drawing is run to the same standard.

Unfinished, always

Every board is supplied unfinished and sanded. Priming, staining and clear-coating happen on site after fitting, by your finisher — which also means the reveal, the tongue and the back get sealed, not just the face.

Cut allowance

Order 10–15% over the net wall or ceiling area for cuts, end matching and grain selection. The written quote carries that allowance as a line you can see, not buried in the footage.

Terms on a custom run

Milled-to-order material is a custom order: a 50% non-refundable deposit releases the run, and custom and cut-to-length items are non-returnable. Shortage or damage claims within 3 business days of receipt. Store policies →

Timing

Production timing depends on the lumber on hand, the knives to set and the shop schedule that week, so it is confirmed on the written quote rather than promised on the page. Will-call at NW Houston / Tanner Rd, or Houston-metro delivery scheduled on the quote.

Coverage

UWP-milled boards carry the one-year material-and-workmanship coverage of the UWP warranties. Movement, checking and colour change from site conditions or finishing are not defects. All warranties →

In-house milling

Send your wall — we'll mill the shiplap.

Four details make the quote clean. Tell us the wall, the board and reveal, the species and finish plan, and the timing — we'll recommend a width, confirm coverage and quote the run with a lead time.

NW Houston · Tanner Rd Yard · Will-call & metro delivery

The wall

Height, width, corners and openings — or total square footage. We add a 10–15% cut allowance on the quote.

Board & reveal

Nominal width (1x6 is standard) and the reveal: flush, 1/8", 1/4" or 1/2". Horizontal or vertical helps us set lengths.

Species & finish plan

Paint-grade Poplar or a stain-grade hardwood, and whether it is painted, stained or clear-coated on site.

Lengths & timing

Random lengths or specified; pickup date. Material is milled to order at NW Houston / Tanner Rd and staged for will-call.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

What is shiplap, exactly?
A board with a rabbet — a stepped notch — milled along each edge on opposite faces, so the boards overlap and self-space. UWP shiplap is solid wood, milled to order — not a thin MDF panel printed to look like boards — so it sands, stains and finishes like any hardwood.
Which species can you run?
Paint-grade Poplar, Red Oak, White Oak, Maple, Walnut and Hickory are the core quoted species. Other species are milled to order, with timing confirmed on the written quote.
How wide is the gap between boards?
Your choice: flush (no reveal), or a 1/8", 1/4" or 1/2" reveal. The 1/4" gap is the popular nickel-gap look. The rabbet is milled to hold the reveal, and a spacer at install keeps it true.
What sizes and widths?
Catalogue runs are 1x4 through 1x12 at 3/4" nominal thickness, with 1x6 the standard; 1x10 and 1x12 are subject to availability. Custom thicknesses and widths are milled on request.
How much coverage does a board give?
A 1x6 covers about 5-1/4" per course at a 1/4" reveal — the 5-1/2" face less the 1/2" lap, plus the gap. The table above lists the other widths; the written quote confirms coverage for the reveal you choose and includes a cut allowance.
Should the boards run horizontally or vertically?
Horizontal is the traditional run and the easier install: the courses stack off a level line and nail straight into the studs. Vertical reads taller and more contemporary, but the wall needs horizontal furring or blocking to nail into. Either way, tell us the direction — it sets the lengths we mill.
Can shiplap go in a bathroom or kitchen?
In a conditioned room, yes — a powder room, a kitchen wall, a laundry. Finish every face, including the back and the rabbet, before it goes up, and keep it out of the direct splash zone of a shower or tub. Covered porch ceilings are the only exterior use; the quote confirms species and back-priming for the exposure.
Shiplap or tongue and groove?
Shiplap overlaps and is the easier board to fit, with the reveal as its feature. Tongue and groove interlocks, holds flatter across a long span, and hides the fastener in the joint — the usual call for ceilings and soffits. See hardwood tongue & groove.
Do you show pricing here?
No — shiplap is milled to order and quoted by species, width, reveal and footage. Send the wall through the quote form or call the Tanner Road yard and we will price the run.
Pickup or delivery?
Current material availability, production timing, pickup, and delivery are confirmed on the written quote after UWP reviews the exact SKU, species, quantity, geometry, and shop capacity.

Part of our hardwood millwork program. Also milled to order: tongue & groove and wall paneling.

All answers →