How do I acclimate hardwood before installing it?
Acclimate hardwood by stacking the material in the install space — not the garage, not the porch — for 5 to 7 days before installation. The room must be HVAC-conditioned at typical living temperature and humidity. The wood reaches equilibrium moisture content with the room and will not move significantly after install. Skipping this step is the #1 cause of post-install gaps, cupping, and squeaks.
The short version
- Where: stack the material inside the install space — same temperature and humidity the wood will live in. Not the garage, not the back porch, not a job-site trailer.
- How long: 5 to 7 days is the residential standard. Thicker stock and lower-humidity regions need longer; very dry, conditioned spaces can sometimes go to 5.
- Stack with airflow. Use stickers (small spacers) between layers so air moves around every board. Don’t shrink-wrap, don’t stand against a wall in a stack.
- Skipping this is the #1 install mistake. The wood will reach equilibrium moisture with or without you — better to do it before fasteners go in.
The full answer
Wood is hygroscopic — it absorbs and releases moisture from the air until it reaches an equilibrium with its environment. Every piece of hardwood we mill is at the moisture content of our Houston shop on the day it leaves. The room you’re installing it in is almost certainly at a different moisture content — drier, wetter, warmer, cooler. The wood will move to match. Acclimation is just letting that movement happen before you fasten the wood down, instead of after.
The basic procedure
- Bring the wood into the install space — same room, or as close as possible. A bedroom acclimating for hallway install is fine. The garage is not. A porch is not. A trailer or jobsite shed is not.
- Stack with stickers — small wood spacers (3/8″ to 3/4″) between every layer so air can circulate around every board. Boards stacked tight to each other won’t breathe.
- Wait 5 to 7 days. Don’t fasten anything for the first 5 days; check moisture content with a meter (or wait the full 7) before installing.
- Confirm the room is HVAC-conditioned during acclimation — running heat in winter, AC in summer. Acclimating in a closed-up house with no climate control is acclimating to the wrong target.
How long is really long enough?
5 to 7 days is the residential standard for stair treads, flooring, and mouldings of typical thickness (3/4″ to 1″). Thicker stock — custom thick stair treads (1¾″ to 3½″), heavy countertops — needs 7 to 14 days because the wood has more mass to equilibrate.
A moisture meter removes the guesswork. Read the moisture content of the wood, then the moisture content of the existing wood structure in the install space (a hardwood floor, a wood subfloor, an existing trim piece). When the two are within 2 percentage points, the wood is acclimated. Most professional installers check this before fastening; serious DIYers should too.
Houston-specific notes
In an HVAC-conditioned Houston home, interior humidity runs in a normal range year-round — typically 30%–55% RH. The wood we sell is milled to a moisture content that targets this range. Acclimation in a conditioned Houston interior is usually quick. The risk is the in-between space: the garage stack, the porch storage, the construction trailer at a build site. These spaces can be 70%+ RH in summer, and wood stored there absorbs moisture you’ll have to release after install.
New-construction sites with no AC are especially risky. Don’t install hardwood until the HVAC is running and the space has been conditioned for at least 2–3 weeks. Installing in an open shell will result in the wood swelling, then shrinking once the AC comes on, leaving permanent gaps.
What goes wrong when you skip it
- Cupping — boards that absorbed moisture in storage release it after install, curling at the edges. Visible as a “smile” or a “frown” across the board face.
- Gaps — boards that were too wet shrink as they dry to the room, leaving thin gaps at every seam.
- Crowning — the opposite of cupping; boards that were too dry swell after install, pushing up in the middle.
- Squeaks — the relative movement of wood against fasteners over the first months of life produces squeaks that can’t be fixed without pulling everything up.
- Cracking — extreme moisture changes can split wide pieces along the grain.
Every one of these is install-time avoidable. Acclimating costs you a week of waiting; not acclimating costs you a re-install.
When stickering and stacking matters more
For thick custom treads (1¾″+) and wide-plank countertops, sticker the stack with care. Boards stacked tight without airflow will equilibrate unevenly — the outside faces will adjust while the inside faces lag. The board ends up internally stressed and may twist or cup after install. Use uniform-thickness stickers (rip a few from scrap stock if needed), placed every 18″ to 24″ along the length, lined up vertically through the stack.
At a glance
| Product | Acclimation time | Notes |
|---|---|---|
| 1″ stair treads, mouldings | 5 to 7 days | Residential standard. |
| Thick stair treads (1¾″–3½″) | 7 to 14 days | More mass, longer equilibration. |
| Wood countertops | 7 to 14 days | Thick, wide, sometimes both. |
| Standard mouldings | 3 to 5 days | Thinner stock, faster to equilibrate. |
| Custom thick mouldings (built-up crown) | 5 to 7 days | Treat like a tread. |
Related products at UWP
Stair Tread & Riser Installation Guide
PDFFull install reference, with acclimation specifics.
Open PDF →Wood Movement Calculator
ProductSee how much your species and width can move under humidity.
View →How to Install Hardwood Stair Treads
ProductThe full install walkthrough — acclimation is step 1.
View →Wood Species Cheat Sheet
ProductSpecies behavior — some move more than others.
View →Related questions
Terms on this page
Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.
Ask the Houston teamPublished 2026-05-27

