Shiplap vs. tongue and groove — what’s the actual difference, and which should I use?
Shiplap is a rabbeted lap joint: each board overlaps its neighbour, so the seam can hold a deliberate gap — the reveal. Tongue and groove is a mechanical joint: a tongue on one edge seats in a groove on the other, locking boards flat and hiding the fastener. Shiplap is for a visible line. Tongue and groove is for a flat, continuous surface, especially overhead.
The short version
- Shiplap — a 1/2″ rabbet on opposite faces of opposite edges. Boards lap. You choose the reveal: flush, 1/8″, 1/4″.
- Tongue and groove — a 1/4″ tongue seats in a matching groove. Boards lock together and stay coplanar.
- The seam is the decision: shiplap shows a line on purpose, tongue and groove closes up and disappears.
- Overhead, tongue and groove wins. The joint carries the board; a lapped board on a ceiling can sag at the seam over a long run.
- Both are blind-nailed at UWP — through the rabbet or the tongue shoulder — so no face fasteners show.
The full answer
The two joints answer different questions. Shiplap asks *how wide do you want the shadow line?* Tongue and groove asks *how flat do you need this to stay?* Both are milled to order at Tanner Road from the same solid stock, on the same 3/4″ nominal thickness, in the same species. The knife is the only thing that changes — and it changes what the wall does.
How the shiplap joint works
Shiplap is a rabbeted lap. A 1/2″ rabbet is cut to half the board’s thickness, on the front face of one edge and the back face of the other. Set two boards side by side and the rabbets nest: the lap hides the seam from the side, from light, and from air, while the face reading stays open. Because the overlap is a lap and not a lock, you can pull the next board back a deliberate distance and leave a reveal.
- Flush — boards pushed tight. Reads as a continuous plank wall with a hairline.
- 1/8″ reveal — the "nickel gap" look. A US nickel is just under 1/8″ thick, and the trade rounds to 1/8″.
- 1/4″ reveal — a deliberate architectural line. Reads modern; the shadow does the work.
- A deeper lap can be ground in-house when the reveal you want approaches the lap depth — past that, the boards stop overlapping and the gap becomes a hole.
How the tongue-and-groove joint works
Tongue and groove is a mechanical joint, not a lap. One edge carries a projecting tongue — 1/4″ on UWP stock — and the other carries a groove milled to receive it. When the tongue seats, the two boards are locked in the same plane. Neither can cup independently of its neighbour, and neither can drop below the other at the seam. That is the whole point.
The fastener goes through the tongue shoulder at roughly 45 degrees. The next board’s groove slides over it and buries it. Nothing shows on the face, and nothing needs filling. Shiplap is blind-nailed too — through the rabbet, under the lap — but on tongue and groove the joint itself is doing structural work, which is why it is the right call overhead and on long spans.
Which one for which job
| Situation | Use | Why |
|---|---|---|
| Feature wall where the line is the design | Shiplap | You pick the reveal and the shadow is deliberate |
| Ceiling, porch soffit, covered outdoor run | Tongue and groove | The joint carries the board; laps can sag overhead |
| Wainscot below a chair rail | Either | Short runs, well fastened — pick on the look you want |
| Long unbroken wall, boards running horizontal | Shiplap | The reveal absorbs small width variation across a long run |
| Anywhere boards must read as one flat plane | Tongue and groove | Locked edges keep neighbours coplanar |
| A wall you may want to take apart later | Shiplap | Lapped boards come off one at a time; T&G unzips from an end |
What stays the same either way
- Acclimation. Both are solid wood. Sticker the bundle in the room it will live in, with the HVAC running, before a single board goes up. Houston makes this non-negotiable.
- Species. Paint-grade poplar keeps a wall quiet and lets the joint do the work. Red oak, white oak, hard maple, walnut and hickory turn the same profile into the feature.
- Cut allowance. Order more than the bare square footage. A written quote from UWP carries a 10–15% cut allowance for exactly this reason.
- Unfinished. Material ships unfinished. Tone and figure vary board to board, which is what makes it look milled rather than printed.
One thing neither joint fixes: a wall that is not flat. Both profiles telegraph a bowed stud or a proud drywall seam. Shim the framing or add furring strips before cladding, and check the first board with a level in both directions — every board after it inherits that line.
Related products at UWP
Shiplap
CatalogRabbeted shiplap milled to order in solid hardwood or paint-grade poplar, with the joint drawn in section so you can read the reveal before you order.
View →Tongue and groove
CatalogSolid tongue-and-groove boards with a 1/4″ tongue, milled to order in your species and width, blind-nailed through the tongue.
View →Hardwood millwork
CatalogDimension stock, shiplap, tongue and groove, paneling and work surfaces — surfaced and profiled on our own floor.
View →Related questions
- How much shiplap do I need, and how does the reveal change the coverage?
- How do you install a tongue-and-groove ceiling?
- Wainscoting styles — beadboard, shiplap, board-and-batten, raised panel. Which one for my room?
- Paint-grade or stain-grade — how do I choose, and is poplar the right paint-grade wood?
Terms on this page
Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.
Ask the Houston teamPublished 2026-09-14

