What changes when the stair goes commercial.
The same flight, drawn to two codes. Requirements below are pulled from the residential and commercial reference tables on this site, so they cannot disagree with them — the third column is what the difference costs you in parts.
Reflects 2021 IRC · 2021 IBC · ICC A117.1. Adoption is local and amended — confirm the edition your authority having jurisdiction has adopted.
Three things that decide everything else.
The comparison only makes sense once these are settled, and all three are settled by somebody other than the millwork supplier.
- Which code governs. The IRC covers one- and two-family dwellings and townhouses; nearly everything else falls under the IBC. A multi-family building is not automatically residential in the code sense.
- Which edition is adopted. Adoption is local and amended, and jurisdictions commonly run an edition or two behind. The governing document is whichever the authority having jurisdiction has adopted, not the newest published.
- Whether the stair is part of the means of egress. A feature stair in a lobby may be unregulated as egress if the required exits are elsewhere — and that is usually the stair hardwood is specified for.
Stair geometry
The commercial stair is shallower and wider. Most of the difference lands on the tread, and a stair drawn to residential proportions rarely survives the change without a redesign.
| Requirement | Residential · IRC | Commercial · IBC | What changes |
|---|---|---|---|
| Stair width | 36″ minimum clear above the handrail height. Below the handrail: 31½″ clear with one rail, 27″ with rails both sides.R311.7.1 | 44″ minimum clear. 36″ where the stair serves an occupant load under 50.1011.2 | Commercial width is driven by occupant load rather than by a fixed minimum, so it is calculated rather than looked up. Wider stairs also change the tread order: beyond a certain width an intermediate handrail becomes necessary, and treads may exceed the widths a single edge-glued panel is made in. |
| Riser height | 7¾″ maximum, tread top to tread top.R311.7.5.1 | 4″ minimum to 7″ maximum.1011.5.2 | The commercial maximum is lower. A flight laid out to the residential maximum will gain risers when the same floor-to-floor height is built commercially, which lengthens the total run and often forces a landing that was not in the residential layout. |
| Tread depth | 10″ minimum, measured horizontally nosing to nosing.R311.7.5.2 | 11″ minimum, measured horizontally nosing to nosing.1011.5.2 | The commercial minimum is deeper. This is the change that most often makes a stocked tread the wrong part: a depth that suits a residential run may be under the commercial minimum once the nosing is subtracted. |
| Uniformity between steps | No more than 3/8″ between the largest and smallest riser in a flight.R311.7.5.1 | No more than 3/8″ between the largest and smallest riser, or tread, in a flight.1011.5.4 | Both codes limit variation within a flight and both are tight. The practical consequence is identical in either: an overlay tread raises the walking surface and shortens the top rise, so a retrofit has to be measured before it is ordered. |
| Nosing projection | ¾″ minimum to 1¼″ maximum where the tread depth is under 11″. Not required at 11″ or deeper. Variation ≤ 3/8″.R311.7.5.3 | 1¼″ maximum beyond the tread below. Uniform size throughout, including the floor edge at the top of the flight.1011.5.5.1 · 1011.5.5.2 | Similar in both, and in both it is the dimension that decides whether a tread profile can be used as drawn. Projection is measured from the riser face below, not from the front of the board. |
| Nosing profile | Radius of curvature ≤ 9/16″; bevel ≤ ½″.R311.7.5.3 | Curvature or bevel not less than 1/16″ and not more than 9/16″ from the foremost projection.1011.5.5 | Both limit how sharply the leading edge may be radiused or bevelled. A full bullnose sits comfortably inside either; the profiles that get questioned are the heavily rounded ones. |
| Solid risers | Permitted, but where the flight rises more than 30″ the opening between treads must not pass a 4″ sphere.R311.7.5.1 | Solid, vertical or sloped under the tread above at not more than 30° from vertical. Open risers only where the stair is not on an accessible route and the opening rejects a 4″ sphere.1011.5.5.3 | Open risers are permitted far more narrowly in commercial work, and on an accessible route they are effectively ruled out. An open-riser design that reads as contemporary in a house usually becomes a closed-riser stair in a commercial fit-out. |
| Landings | Required at the top and bottom of each stairway. Width not less than the stair; 36″ minimum in the direction of travel.R311.7.6 | Width not less than the stair. Length in the direction of travel not less than the stair width, but need not exceed 48″ on a straight run.1011.6 | Both require a landing at the top and bottom and limit the rise between them. Commercially the limit tends to bite sooner, which means an extra landing platform and the landing tread to finish it. |
| Vertical rise per flight | 12′-7″ (151″) maximum between floor levels or landings.R311.7.3 | 12′ maximum between floor levels or landings.1011.8 | A cap on how far a single flight may climb before a landing is required. It is the rule that turns a straight residential run into a dog-leg commercial one. |
Handrails
The grip rules are close to identical. What changes is how many rails there are, and what happens at the ends of the flight.
| Requirement | Residential · IRC | Commercial · IBC | What changes |
|---|---|---|---|
| Where required | At least one side of every flight with four or more risers.R311.7.8 | Both sides of every stair. Also both sides of ramps with a rise over 6″.1011.11 · 1014.1 | Commercial stairs generally need a handrail on both sides, and wide flights need an intermediate rail as well. That is more rail, more fittings and more newels than the same stair detailed residentially. |
| Height | 34″ minimum to 38″ maximum, measured vertically from the sloped line of tread nosings.R311.7.8.1 | 34″ minimum to 38″ maximum above the nosing line, uniform along the flight.1014.2 | The permitted range is effectively the same in both, measured vertically from the nosing line rather than from the floor. |
| Type I grip | 1¼″ minimum to 2″ maximum outside diameter.R311.7.8.5 | Circular 1¼″–2″ outside diameter, or non-circular with a 4″–6¼″ perimeter and 2¼″ maximum cross-section.1014.3.1 | The same grip categories apply in both. Perimeter is the number that decides it, and it is not something to judge by eye — a wide flat cap that looks generous is the profile that most often fails. |
| Type II grip | Perimeter over 6¼″ with a graspable finger recess on both sides: recess 5/16″ deep within 7/8″ below the widest point, and the rail above the recess 1¼″ to 2¾″ wide.R311.7.8.5 | Perimeter over 6¼″ with the finger recess described in the residential table.1014.3.2 | The decorative alternative in both: a larger profile qualifies only if it carries a finger recess of the specified depth on both sides below the widest point. |
| Continuity | Continuous the full length of the flight, from a point above the top riser to a point above the lowest riser. Ends return to a wall or terminate at a newel post or safety terminal.R311.7.8.4 | Continuous without interruption by newel posts or other obstructions.1014.4 | Both require the rail to run the full flight without interruption. Commercially the requirement extends across landings in more situations, which changes how the rail is turned at a dog-leg. |
| Wall clearance | 1½″ minimum between the wall and the handrail.R311.7.8.3 | 1½″ minimum between the rail and any wall or surface.1014.7 | Essentially the same gap in both. It governs bracket selection rather than rail selection. |
| Extensions at the top | No residential equivalent | 12″ horizontal beyond the top riser, returned to a wall, guard or the walking surface.1014.6 | Commercial only. The rail must continue horizontally past the top riser, which needs a fitting to turn or terminate it and something to land it on. This is the single most common thing missing from a stair detailed to residential habits. |
| Extensions at the bottom | No residential equivalent | One tread depth sloped beyond the bottom riser, then returned or continued to the next flight.1014.6 | Commercial only. The rail continues at the slope for the depth of one tread before turning. Like the top extension, it adds fittings and usually a newel that the residential version of the same stair does not have. |
Guards
The sphere rule is the same idea in both, applied at different heights. The load requirement is where commercial work gets structural.
| Requirement | Residential · IRC | Commercial · IBC | What changes |
|---|---|---|---|
| Where required | Open sides of stairs, landings, balconies and porches more than 30″ above the floor or grade below, measured within 36″ horizontally.R312.1.1 | Open sides of walking surfaces more than 30″ above the floor or grade below, within 36″ horizontally.1015.2 | Both require a guard above a certain drop. The threshold differs, so an edge that needed no guard residentially may need one commercially. |
| Height | 36″ minimum above the walking surface.R312.1.2 | 42″ minimum above the walking surface or nosing line.1015.3 | Commercial guards are taller at floors and landings. A taller guard changes the newel length and, where the same assembly also serves as the handrail, whether it can still be grasped at the required height. |
| Openings | Must not pass a 4″ sphere.R312.1.3 | Must not pass a 4″ sphere.1015.4 | Both express the limit as a sphere that must not pass. The commercial version adds a second, larger sphere for the zone above, which is why a commercial baluster layout can look different from a residential one on the same stair. |
| Stair triangle | The triangle formed by tread, riser and guard bottom rail may not pass a 6″ sphere.R312.1.3 exc. 1 | The tread / riser / bottom-rail triangle may not pass a 6″ sphere.1015.4 exc. 2 | Both relax the sphere at the triangle formed by the tread, the riser and the bottom rail. It is the one place the rule is deliberately looser, and it is worth knowing before adding balusters that are not required. |
Interior finish
This has no residential counterpart at all, and it is the requirement most likely to remove wood from a commercial specification late in the process.
| Requirement | Residential · IRC | Commercial · IBC | What changes |
|---|---|---|---|
| Treads and landings | No residential equivalent | Traditional floor finishes such as wood are exempt from the NFPA 253 critical-radiant-flux test that governs floor coverings.804.1 exception | Commercial only. Treads are treated as floor finish rather than as interior wall finish, which is generally the more permissive classification and is why hardwood treads remain viable in spaces where wood panelling does not. |
| Interior trim | No residential equivalent | Class C minimum — flame-spread index 76–200, smoke-developed ≤ 450 (ASTM E84).806.7 | Commercial only. Trim is assessed separately from wall and ceiling finish, and a limited percentage is typically allowed outside the required class. That allowance is what most hardwood mouldings depend on in commercial work. |
| Combustible trim area | No residential equivalent | Combustible trim may not exceed 10% of the wall or ceiling area of the room — excluding handrails and guards.806.7 | Commercial only. The allowance is a percentage of the wall or ceiling area, so a scheme that is compliant in one room can fail in a smaller one with the same trim package. |
| Handrails and guards | No residential equivalent | Excluded from the 10% combustible-trim cap. Wood handrails and guards are permitted in all construction types.806.7 · 1014 | Commercial only, and useful to know: handrails and guards are treated as part of the stair rather than as interior finish, which is why a wood rail can appear where wood panelling cannot. |
Each code in its own right.
This page compares. The reference pages carry every row, every citation and the UWP part that meets each line.
Taking a residential detail commercial?
Send the stair section and the adopted code edition. We will tell you which parts survive the change and which need redrawing.
Questions that come up on these details
What are the IRC stair code rules in plain English?
The IRC residential stair code requires a minimum 10″ tread depth, a maximum 7-3/4″ riser height, a 3/4″ nosing overhang, 36″ minimum stair width, 6′8″ minimum headroom, and handrails on at least one side. Variation between any two treads on the same flight cannot exceed 3/8″. Most code violations on retrofit jobs come from changing the tread thickness without re-framing the stair.
Read the answer →Are there commercial or fire-rated stair tread requirements I should know about?
Commercial stair treads in buildings governed by the IBC must meet fire-rating requirements (usually Class A or Class B flame spread), slip-resistance standards, and ADA dimensional rules. Solid hardwood treads can meet most of these requirements with appropriate finish and detailing. Egress stairs in larger commercial buildings often require specific tested assemblies — verify with the project architect or fire marshal before specifying.
Read the answer →What are the standard dimensions of a hardwood stair tread?
A standard hardwood stair tread is 1 inch thick, 10-1/2″ to 11-1/2″ deep (front to back), and stocked in 42″, 48″, and 60″ widths at UWP — with red oak running to 96″. The IRC building code requires a minimum 10″ tread depth with a 3/4″ nosing overhang. Custom widths, depths, and thicknesses are available built to order.
Read the answer →

