What are the standard dimensions of a hardwood stair tread?
A standard hardwood stair tread is 1 inch thick, 10-1/2″ to 11-1/2″ deep (front to back), and stocked in 42″, 48″, and 60″ widths at UWP — with red oak running to 96″. The IRC building code requires a minimum 10″ tread depth with a 3/4″ nosing overhang. Custom widths, depths, and thicknesses are available built to order.
The short version
- Thickness: 1″ is the residential standard. 1¾″ to 3½″ is custom thick-tread territory for open-rise and modern designs.
- Depth (front to back): 10-1/2″ to 11-1/2″ is the standard range. The 8070 bullnose is 11-1/2″ deep; the 8072 square-edge is 10-1/2″.
- Width (side to side): UWP stocks 42″, 48″, and 60″ in all species. Red oak runs to 96″. Wider treads available built to order.
- Code: IRC requires a minimum 10″ tread depth with a 3/4″ nosing overhang on residential stairs.
The full answer
A stair tread has three real dimensions: thickness (how tall the slab is), depth (how far front to back, the part you step on), and width (side to side, parallel to the wall). UWP stocks the standard range in all three; custom is available for anything outside the range.
Thickness
The residential standard is 1″. Our 8070 bullnose and 8072 square-edge full-thickness treads are both 1″ — sized to sit on the rough stair structure as the finished walking surface. The 8071 / 8073 retro-fit versions are 5/8″ at the body with a built-up 1″ bullnose nose, designed to drop onto a carpeted stair without demo.
Custom thick treads run 1¾″ to 3½″ — built to order, used on open-rise stairs, floating stairs, and modern designs where the tread is part of the architecture. These are a different program from the 1″ stocked SKUs (see the thick tread question). Anything thicker than 1″ is generally not retrofit material.
Depth (front to back)
Standard depths:
- 8070 bullnose: 11-1/2″ deep (including the 1-1/4″ bullnose nose overhang).
- 8072 square-edge: 10-1/2″ deep (no extended nose).
- 8071 / 8073 retro-fit: matched to the existing stair’s tread depth at install — the built-up nose accommodates a wide range.
- Landing treads (8091 / 8090): narrower at about 3-1/2″ with a bullnose front — used at the top of a stair where the floor transitions to a landing.
The IRC building code minimum is 10″ tread depth (measured from the front edge of one tread’s nosing to the front edge of the next tread’s nosing). Most residential stairs build to 10″ to 11″ of effective tread depth, with the 3/4″ nosing overhang providing the additional walking surface required by code.
Width (side to side)
UWP stocks 42″, 48″, and 60″ widths across all species — these cover most residential staircases. Red oak runs to 96″ because the underlying lumber is more available in long, clean boards. White oak and the other species typically run to 60″ stock; longer is available built to order.
Code minimum stair width: IRC requires 36″ minimum (between handrails or finished walls). Most residential stairs build to 36″–42″; commercial and high-end residential build wider.
Returned ends and custom shapes
Standard treads have square ends — appropriate for stairs with closed stringers on both sides (the tread butts into the wall trim or the skirt board). Stairs with an open end (visible from the side) need a returned end: the bullnose continues around the side of the tread so no raw end shows. UWP mills returned ends on either or both ends as a configurator option.
Pie / winder treads — for stairs with a turn, where one tread fans out to fit the angle — are custom built. Curved stair treads are templated on-site and milled from the template (see curved stair treads).
Risers
A stair riser is the vertical board between two treads. Standard residential riser height is 7″ to 7-3/4″ (the IRC maximum is 7-3/4″). Risers are typically 3/4″ thick in matching species, with the front of the upper tread overhanging the riser by the 3/4″ nosing standard.
At a glance
| Dimension | Standard | UWP options |
|---|---|---|
| Thickness | 1″ (residential) | 1″ stocked; 1¾″–3½″ custom |
| Depth (front to back) | 10-1/2″ to 11-1/2″ | 11-1/2″ on 8070; 10-1/2″ on 8072; custom on order |
| Width (side to side) | 36″ to 60″ | 42″, 48″, 60″ stocked; red oak to 96″; custom on order |
| Nosing overhang | 3/4″ (code) | 1-1/4″ on stocked 8070 bullnose |
| Riser height | 7″ to 7-3/4″ (code max) | Custom to match new stairs |
The configurator handles all four dimensions plus species and profile — open it to see real pricing on your project’s exact spec.
Related products at UWP
8070 Bullnose Stair Tread
Product11-1/2″ deep, 1″ thick, 42″–96″ widths.
View →8072 Square-Edge Tread
Product10-1/2″ deep, 1″ thick. Modern profile.
View →Custom Stair Tread Configurator
ConfiguratorCustom widths, depths, and profiles. Planning estimate with UWP review.
View →Stair Tread & Riser Installation Guide
PDFStep-by-step install reference with diagrams.
Open PDF →Related questions
Terms on this page
Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.
Ask the Houston teamPublished 2026-05-27

