Skip to main content
Unique Wood Products

What are the IRC stair code rules in plain English?

The IRC residential stair code requires a minimum 10″ tread depth, a maximum 7-3/4″ riser height, a 3/4″ nosing overhang, 36″ minimum stair width, 6′8″ minimum headroom, and handrails on at least one side. Variation between any two treads on the same flight cannot exceed 3/8″. Most code violations on retrofit jobs come from changing the tread thickness without re-framing the stair.

The short version

  • Tread depth: minimum 10″ (front of nosing to front of next nosing). Most stairs build to 10″–11″.
  • Riser height: maximum 7-3/4″. Most stairs build to 7″–7-3/4″.
  • Uniformity: 3/8″ maximum variation between any two risers or any two treads on the same flight.
  • Width: 36″ minimum. Headroom: 6′8″ minimum. Handrails: at least one side; 34″–38″ above the nosing.

The full answer

The IRC (International Residential Code) sets the residential stair rules in most US jurisdictions, including Houston. Below is the working version — the rules an architect, builder, or remodeler actually has to hit. Local amendments may modify some of these; check your jurisdiction for specifics, but the IRC is the floor.

Tread depth — minimum 10″

The IRC requires minimum 10″ tread depth, measured from the front edge of one tread’s nosing to the front edge of the next tread’s nosing. This is the horizontal walking surface the code cares about. With a standard 3/4″ nosing overhang and a 9-1/4″ riser-to-riser run, you get exactly 10″ of effective tread depth.

Most well-built residential stairs run 10″ to 11″ of tread depth. Anything wider feels luxurious; anything narrower is potentially out of code. UWP’s standard 8070 bullnose is 11-1/2″ deep including the 1-1/4″ nosing — well above code minimum.

Riser height — maximum 7-3/4″

The IRC caps riser height at 7-3/4″, measured vertically from the top of one tread to the top of the next. Going taller is the most common code violation on DIY stair builds — and it’s easy to do accidentally if you’re trying to fit a stair into a short total rise with too few steps.

Most residential stairs run 7″ to 7-3/4″ of riser height. Custom homes and high-end residential sometimes go lower (6-1/2″ to 7″) for comfort.

The uniformity rule — 3/8″ max variation

On any single flight of stairs, no two risers can differ by more than 3/8″, and no two treads can differ by more than 3/8″. This rule is the reason you can’t retrofit thick stair treads over an existing stair: adding a 1¾″ tread on top of every step except the top one makes the top step’s riser 1¾″ shorter than every other step, which is way over the 3/8″ allowance.

The uniformity rule is about safety: people walk stairs on muscle memory after the first step or two. Inconsistent rise heights cause falls.

Nosing overhang — minimum 3/4″

The IRC requires a 3/4″ minimum nosing overhang — the front edge of the tread extends 3/4″ beyond the face of the riser below it. This is the “lip” of the tread that you see from the front.

Exception: if the tread depth is 11″ or greater (including the overhang), the code doesn’t require a separate overhang. Many modern open-rise designs use this exception to build square-edged stairs without a nosing — they just make the treads wide enough to compensate.

Stair width — minimum 36″

Stair width of 36″ minimum, measured from one finished wall (or handrail) to the other finished wall (or handrail). Most residential stairs build to 36″–42″; commercial and high-end residential build wider.

Headroom — minimum 6′8″

Headroom of 6 feet 8 inches minimum, measured vertically from the nosing of any tread to whatever is above it (typically the underside of the floor or stair above). This is the rule that constrains stair location in a remodel — you can’t just put a stair anywhere a stair fits; it has to have full-height clearance over every step.

Handrails — at least one side, 34″–38″ above the nosing

At least one handrail is required on any stair with 4 or more risers. The handrail runs from the nosing of the top tread to the nosing of the bottom tread, continuous, at a height of 34 inches to 38 inches above the line connecting the nosings.

The handrail must be graspable — round profiles 1-1/4″ to 2″ diameter, or rectangular profiles meeting specific cross-section rules. The visible decorative cap on a fancy stair railing has to actually be grippable; “for-show” handrails fail inspection.

At a glance

RuleCode minimum/maximumNotes
Tread depth10″ minimumFront-of-nosing to front-of-next-nosing.
Riser height7-3/4″ maximum7″–7-3/4″ standard.
Uniformity3/8″ max variationAcross all treads and risers on a flight.
Nosing overhang3/4″ minimumOr 11″+ tread depth without one.
Stair width36″ minimumBetween finished walls or handrails.
Headroom6′8″ minimumVertical from every nosing.
Handrails34″–38″ above nosingsOn 4+ risers, graspable profile.

Where stair retrofits usually break code

  • Adding tread thickness without re-framing. The 8071 retro-fit tread is 5/8″ + 1/16″ glue = ~11/16″ — adjusted to match the existing skirt board. A full 1″ retro-fit changes the top riser by 1″, which on a typical 7-1/2″ rise is 3/4″ off code uniformity. The 8071 design exists specifically to avoid this.
  • Curving a runner around a turn in a way that drops a tread depth below 10″ at the inside of the curve — the winder tread rule requires the depth measured at a specific point (the walking line), not the inside corner.
  • Replacing handrails with non-graspable decorative pieces — flat-top railings, art-piece sculptural rails, etc. Need a separate graspable rail.

Local Houston / Texas amendments

Houston building code is largely aligned with the IRC. The most common local modification on stair work is inspection sign-off requirements — major remodels often require a building permit and a final inspection, even for a stair refinish. Check with the City of Houston or your local jurisdiction before starting a significant stair project. For routine tread replacement (one-for-one) without changing the structural geometry, permits usually aren’t required.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-27