Moulding family
Wall Paneling Boards
12 profiles · 12 milled to order
These are the board profiles for a panelled wall — shiplap, nickel-gap and V-groove — each defined by the joint at its edge rather than the face. A shiplap board carries a rabbet on opposite faces so the boards overlap and leave a reveal; nickel-gap is the same joint milled to a fixed 3/16″ shadow line; V-groove is a tongue and groove with a chamfer that reads as a line when the boards close up.
The mill cuts them in solid hardwood or paint-grade to the width and reveal on the drawing. The full programme, with species, widths and the installation guide, is on the hardwood wall paneling page; the profiles here are the sections themselves, each with a spec sheet and a DXF.
Narrow the 12 profiles by style (1) below, or use the catalogue's finder for a SKU.
Narrow it down

Wall Paneling Lap & Gap
3-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Lap & Gap
5-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Lap & Gap
7-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Lap & Gap
9-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling V-Groove
3-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling V-Groove
5-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling V-Groove
7-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling V-Groove
9-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Penny Gap
3-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Penny Gap
5-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Penny Gap
7-1/4" × 3/4"
Milled to orderView profile →
Wall Paneling Penny Gap
9-1/4" × 3/4"
Milled to orderView profile →Terms used on this page
Questions people ask before ordering
Wainscoting styles — beadboard, shiplap, board-and-batten, raised panel. Which one for my room?
Wainscoting is wall paneling that covers the lower 30 to 48 inches of a wall. Five main styles: beadboard (narrow vertical strips with bead detail), shiplap (horizontal overlapping boards), board-and-batten (flat panels with vertical battens), flat-panel (simple recessed squares), and raised-panel (formal beveled panels). Pick on home style — beadboard for farmhouse, shiplap for coastal, raised panel for traditional formal.
Read the answer →Does Houston humidity damage hardwood floors and stair treads?
Houston outdoor humidity is high year-round, but conditioned indoor humidity stays in a normal range (30%–55% RH) — the same as most US homes. Hardwood floors, stair treads, and mouldings installed in conditioned Houston interiors perform as well as anywhere else in the country. The risk isn’t the climate; it’s installing wood in an unconditioned space or skipping acclimation.
Read the answer →How do I acclimate hardwood before installing it?
Acclimate hardwood by stacking the material in the install space — not the garage, not the porch — for 5 to 7 days before installation. The room must be HVAC-conditioned at typical living temperature and humidity. The wood reaches equilibrium moisture content with the room and will not move significantly after install. Skipping this step is the #1 cause of post-install gaps, cupping, and squeaks.
Read the answer →Polyurethane vs. oil finish on hardwood — which one should I use?
Polyurethane is a film-forming finish — it sits on top of the wood, harder and more abrasion-resistant, but harder to repair locally. Oil finishes (Rubio Monocoat, Osmo, tung oil) penetrate into the wood, look more natural, and are easier to spot-repair — but provide less surface protection. Pick polyurethane for stairs and high-traffic floors; oil for countertops, lower-traffic floors, and natural-look projects.
Read the answer →

