
Red Oak
Core catalogPairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.
The finished bullnose edge where a staircase meets the upstairs floor or a landing. A solid 1" hardwood nosing strip with a built-in rabbet that laps the adjoining flooring for a flush transition. Edge-glued, never veneered, milled in-house in Red Oak and White Oak.

8091 landing tread — bullnose nosing with a rabbeted underside
Profile
3-1/4" / 5-1/4" × 1"
Shown as an indication of colour, not a figure sample. Grain and colour vary board to board.
Reddish tone, prominent open grain — the standard match for red oak stairs and floors. 3-1/4" wide with a 1/2" rabbet — laps over 1/2" flooring.
This profile has no published section drawing yet — the spec sheet carries the dimensions we hold.
Need a non-stock species, a curved stair, or a length we don't stock? Our mill custom-runs and templates to spec — see Custom Stair Treads.

Crafted in-house · NW Houston / Tanner Rd
Explore photographs of UWP treads, curved details, and custom fabrication.
The landing tread is the narrow nosing strip where the last riser meets the upstairs floor. It carries the same 1" thickness and nose as the treads below, and a rabbet on its back underside lets the flooring tuck under it.
Stocked in 3/8", 1/2" and 3/4" rabbets for the common flooring thicknesses. Other depths are cut to order.
3-1/4" is the standard nosing; 5-1/4" shows more hardwood at the stair head. Length runs wall to wall, or around a balcony edge with mitered corners.
Full bullnose to match 8070 treads, or eased edge for a square-edge stair, so the top step reads like the rest.
Where the strip ends at an open balcony corner, a 1-1/4" returned end wraps the nose around the corner instead of leaving raw end grain.
A riser is the upright board that closes each step. It stands on the tread below, the tread above sits on it, and the tread's nose hangs 1-1/4" past its face. Every step has one, and a flight has one more rise than it has treads.
Most staircases run a painted white riser under a stained tread — that is the primed 1/2" piece. For a riser in the same wood as the tread, use 3/4" hardwood S4S from the yard in Red Oak, White Oak, Maple or Hickory and stain it with the treads.
Top of one tread to the top of the next, on three steps of the flight. Stock is 7-1/2" tall, which is more than any residential rise leaves showing once the tread sits on it, so the riser is ripped down to fit on site — never built up.
Skirt to skirt across the step, at the back where the riser sits. On an open side, to the finished face of the stringer. Measure the top, middle and bottom steps.
A flight has one more rise than treads. Each 90" primed piece cuts into 2 risers for any stair up to 44" wide; wider than that, count one piece per rise. Hardwood S4S comes in random lengths — give us the count and the width and the yard pulls boards to yield it.
The riser is fitted first and the tread lands on it, nose 1-1/4" proud of the riser face. A small cove or bull nosing from the stair-moulding line covers the joint between them.
| Primed white riser | Hardwood S4S riser | |
|---|---|---|
| Size | 1/2" thick × 7-1/2" tall | 3/4" thick × 7-1/2" tall |
| Length | 90" long — usually two standard risers per piece | Random lengths as the yard has them — cut to the width of each step on site |
| Species | Paint-grade, primed white | Red Oak · White Oak · Maple · Hickory |
| Finish | Ready for your topcoat | Unfinished, surfaced four sides — stain to match the treads |
| Sold as | By the 90" piece | By the board, from the yard |
| Best for | The classic painted riser under a stained tread — and the retro-fit overlay, thin enough to cap an existing riser without moving the nose. | A stained riser that matches the tread species, or a painted riser in solid wood on a new build. |
Hardwood S4S lengths and species on hand are the yard's day-to-day stock — confirmed at quote. See hardwood S4S & S3S for the dimension-stock program.
Worked count
A straight flight of 12 treads has 13 rises — one more than the treads, because the first rise is from the floor to the first tread and the last is up onto the landing. On a stair 42" wide, each primed piece cuts into 2, so order 7 primed pieces. In hardwood S4S, tell us 13 risers at 42" and the yard pulls the boards to yield it.
The landing tread is the visible edge where the stair meets the upstairs floor — it should match both. Species is chosen for tone, not just hardness; pick the one closest to your flooring so the transition disappears.
Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.
Send a sample of your floor — we'll species-match the run.
Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.
Red Oak
White Oak
Hard Maple
Hickory
Walnut| Species | Hardness | Color & appearance | Grain & texture | Availability |
|---|---|---|---|---|
Red Oak | 1290 lbf | Light-to-medium brown with a reddish cast; stains slightly pink. | Bold, prominent grain lines with occasional swirl. | Core catalog |
White Oak | 1350 lbf | Light-to-medium brown with an olive, not pink, cast. | Medium-to-coarse, slightly open structure. | Core catalog |
Hard Maple | 1450 lbf | Creamy white to light reddish-brown; clean and modern. | Mostly straight, sometimes wavy; fine, even texture. | Made to order |
Hickory | 1820 lbf | Creamy lights against rich browns; rustic and striking. | Coarse, pronounced, high-contrast figure. | Made to order |
Walnut | 1010 lbf | Deep, luxurious chocolate tones; warm and refined. | Fine-to-medium grain, smooth and elegant. | Made to order |
These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.
Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →
No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.
Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.
Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.
North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.
Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.
Where the staircase meets the upstairs floor you need a bullnose that matches the treads and laps the flooring. That is the landing tread — the rabbet does the lapping.
The bullnosed edge at the top of a flight where the last riser meets the upstairs floor.
The finished nosing around an open landing edge, matched to the treads below.
The built-in rabbet laps the adjoining flooring so the nosing sits flush, not proud.
Species-matched to 8070 treads and risers for one continuous staircase.
Straight answers to the questions we field at the will-call counter — not a marketing FAQ.
The 8070 is a full 1″ tread for new builds or full demos. The 8071 is a 5/8″ retro-fit overlay built to drop over carpeted stairs without demolition. The key reason: when you pull the carpet, the wood skirt board next to the staircase is roughly 11/16″ thick. The 8071 lands flush against it. The 8070 sits about 1/4″ proud and looks unfinished.
Read the answer →A standard hardwood stair tread is 1 inch thick, 10-1/2″ to 11-1/2″ deep (front to back), and stocked in 42″, 48″, and 60″ widths at UWP — with red oak running to 96″. The IRC building code requires a minimum 10″ tread depth with a 3/4″ nosing overhang. Custom widths, depths, and thicknesses are available built to order.
Read the answer →Bullnose treads have a rounded front edge that overhangs the riser — the traditional look in American homes. Square-edge (and eased) treads have a straight or slightly softened front edge — the modern look. Both meet code with a 3/4″ nosing. Pick bullnose for traditional and transitional designs; square or eased for modern, contemporary, and minimalist projects.
Read the answer →Match new stair treads to existing floors in three steps: confirm the floor species (red oak and white oak look similar but stain very differently), order unfinished treads in the same species, and have the same finisher stain and topcoat both the floor and the treads with the same can. Pre-finished stair treads almost never match a site-finished floor exactly.
Read the answer →