Skip to main content
Unique Wood Products

Custom 8090 Landing Tread

The nosing strip that finishes a landing — full 1" nose over a 3/4" rabbet that laps the finish floor behind it.

  • Instant estimate
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Loading configurator…
Where a landing tread goes

The finished edge
at the top of the stair.

The landing tread is the narrow nosing strip where the last riser meets the upstairs floor. It carries the same 1" thickness and nose as the treads below, and a rabbet on its back underside lets the flooring tuck under it.

  1. Match the rabbet to the flooring

    The rabbet is cut for your flooring thickness — tell us what is going down upstairs and the strip is milled to meet it.

  2. Pick the face width

    3-1/4" is the standard nosing; 5-1/4" shows more hardwood at the stair head. Length runs wall to wall, or around a balcony edge with mitered corners.

  3. Same nose as the treads

    Full bullnose to match 8070 treads, or eased edge for a square-edge stair, so the top step reads like the rest.

  4. Open side? Return the end

    Where the strip ends at an open balcony corner, a 1-1/4" mitered returned end wraps the nose around the corner instead of leaving raw end grain.

Where a landing tread goes at the top of the stairSection at the stair head: a 1 inch hardwood nosing strip sits on the top riser with its nose 1-1/4 inch past the riser face, and the upstairs flooring tucks under a rabbet on its back underside. A second drawing compares the 3-1/4 inch and 5-1/4 inch faces and the rabbet depths cut for 3/8, 1/2 and 3/4 inch flooring.SECTION · AT THE STAIR HEADThe nosing sits on the top riser; the flooring tucks under its back lip.flooringsubfloorheadertop riserrabbetcut to the flooring: 3/8" · 1/2" · 3/4"5-1/4" faceor 3-1/4"1"1-1/4"Drawn to scale · 1" thick · nose 1-1/4" past the riser · rabbet sized to the flooringCHOOSING · FACE WIDTH × RABBETPick the face for the look, the rabbet for the flooring going down upstairs.3-1/4" facethe standard nosing3/8" rabbet5-1/4" facemore hardwood showing3/4" rabbetCustom 8090 / 8092: any depth 3"–6", bullnose or eased edge, rabbet cut to your flooringTHE MITERED RETURNED END · OPEN STAIRCASEOne side of the stair meets a wall; the other is open, so that end shows.The mitered returned end wraps the nose round the open end so no raw board end shows.1 · FROM ABOVEWALL SIDEclosed endcut square,butts the skirtBACKsits against the riser — the upright board of the step aboveFRONT · THE NOSEthe rounded edge you step overoutside face of the stringer(the board the treads sit on)1-1/4"OPEN SIDEno wall — you can seethis end of every stepmitered returned enda 1-1/4" piece with the samenose, fixed to the end so thenose turns the corner andthe raw board end is hidden.It runs 1-1/4" past the back,behind the riser above.2 · STANDING BESIDE THE OPEN SIDEThe same tread seen from the room, looking at its open end.FRONT · THE NOSE← the tread carries on to the wall sideBACK · against the riserOPEN SIDEthe mitered returned endthe same nose, wrappedround the corner — no rawend of the board showingMeasure: wall to the outside face of the open stringer, plus the 1-1/4" returned end.Not reversible: it has a top and a bottom — tell us which side is open.In the configurator: tick Left or Right return under Nosing & Returns.
Top: section at the stair head — the 1" nosing on the top riser, flooring tucked under its back rabbet. Middle: the two stocked faces and the rabbet depths cut for 3/8", 1/2" and 3/4" flooring. Bottom: the returned end at an open corner.
UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the stair disappears into the room instead of fighting it.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Core catalog
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Core catalog
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Specifications

The full spec sheet. For the builder who scrolled this far.

Body1" solid or 5/8" retro-fit
Edge profilesBullnose · eased · mitered returned ends
ConstructionEdge-glued solid — never veneered
SpeciesFive configured hardwoods
DimensionsAny width, depth & length to spec
GeometrySquare, pie, winder, curved, landing
MilledIn-house in Houston, TX
SurfaceUnfinished, sanded
Lead timeConfirmed at quote
Minimum order1 piece
TemplatingOn-site for curved & complex
QuotePlanning estimate in the configurator
Popular wood species

The species we run most.

Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.

Red Oak
Core catalog
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Core catalog
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

What is a landing tread and where does it go?
It is the nosing strip that finishes the edge of a landing or the top of a flight, where the floor stops and the stair begins. It gives that edge the same nose profile the treads below it carry, so the stair reads as one piece instead of a floor that happens to end in a drop.
What is the 3/4″ rabbet on the back for?
The finish floor laps into it. The landing tread carries a full 1″ nose at the front and steps down to a 3/4″ rabbet at the back, so 3/4″ flooring runs up to the edge and tucks underneath. That hides the flooring end grain, takes up the expansion gap, and leaves one clean line at the nose.
What depth should I order?
Enough to carry the nose and land on solid framing behind it — 3″ to 6″ covers most landings. Deeper is the safer choice where the framing at the edge is irregular or where the floor has to stop further back. Measure from the front face of the riser below to where you want the flooring to start.
Bullnose or eased front?
Match the treads in the flight. The bullnose front carries the same full rounded profile as an 8070 tread; the eased front matches an 8072 square-edge tread. Mixing them puts two different nose profiles on the same staircase, which reads as a mistake from across the room.
How does it meet the skirt board and the newel?
The landing tread runs into the skirt the same way a tread does and is scribed to it. Where it passes a newel the newel usually sits on top of it or is notched around it, depending on how the post is anchored — decide that before ordering length, because the post location affects where the piece has to break.
All answers →

Terms used on this page