Skip to main content
Unique Wood Products

8070 vs. 8071 — which stair tread fits my existing staircase?

The 8070 is a full 1″ tread for new builds or full demos. The 8071 is a 5/8″ retro-fit overlay built to drop over carpeted stairs without demolition. The key reason: when you pull the carpet, the wood skirt board next to the staircase is roughly 11/16″ thick. The 8071 lands flush against it. The 8070 sits about 1/4″ proud and looks unfinished.

The short version

  • 8070 (full 1″ tread) → new build, full demo, or any stair where you’re also replacing the substrate. The tread *is* the finished walking surface.
  • 8071 (5/8″ retro-fit) → renovation overlay. Drops onto your existing carpeted stair without tearing it apart. A built-up 1″ bullnose nose covers the front edge of the old substrate so nothing looks unfinished.
  • The skirt-board test: pull up a corner of the carpet. The wood trim running alongside the stairs — about 11/16″ thick — is your reference. The 8071 lands flush against it; the 8070 sits about 1/4″ proud.
  • Practical rule: carpet to remove + skirt board in place → 8071. New build or full demo → 8070.

The full answer

The 8070 is the standard full-thickness tread. Solid 1″ hardwood, edge-glued, bullnose front edge, stocked in red oak and white oak at the NW Houston yard. Use it on new construction, or on renovation jobs where you’re replacing the substrate and rebuilding the stair from the stringers up. It sits on the rough framing as the finished surface.

The 8071 is a renovation overlay. A 5/8″ body with a built-up 1″ bullnose nose. It’s designed for one specific job: pull up the carpet, leave the original rough plywood or pine substrate in place, glue and pin the 8071 on top. The thicker built-up nose wraps the front edge of the old substrate so the seam is hidden. Most jobs install in a weekend, no demo required.

The skirt-board test (the rule installers wish more homeowners knew)

The piece of trim running flat along the wall alongside your stairs is the skirt board. On almost every carpeted stair built in the last 50 years, it’s a piece of nominal 1×8 lumber, actually about 11/16″ thick. The skirt was sized to match the combined height of the carpet and the pad — so the top of the carpet sat flush with the top of the skirt and the install looked finished.

When you pull up the carpet, the skirt is suddenly standing 11/16″ proud of the bare substrate — and that 11/16″ is the reference you need to hit with your new wood tread.

  • 8071 retro-fit: 5/8″ body + a 1/16″ construction-adhesive bed ≈ 11/16″ total, flush with the skirt. No visible step where the tread meets the wall.
  • 8070 full tread: 1″ body sits about 1/4″ proud of the skirt. The skirt now looks recessed against the tread; the visible step at the wall reads as an unfinished install.

That’s why the 8071 exists: it solves the skirt-board problem without asking you to rebuild the stair.

How to pick

If your stair is…Use thisWhy
Carpeted today, you want hardwood, no demo8071 retro-fitLands flush with the existing skirt board. Weekend install.
Carpeted, but you’re gutting it to the stringers8070 full treadYou’re replacing the substrate and skirt anyway.
New construction8070 full treadThe tread is the finished surface from day one.
Existing hardwood you’re refinishingSand the existing treadsIf they sand smooth, you don’t need new treads. Most do.
Want a clean modern edge instead of a bullnose8072 / 8073Square / eased edge versions of the 8070 / 8071. Same skirt-board math.

Both are core catalog species. Red Oak and White Oak variants are listed by exact SKU and width. The NW Houston yard confirms current availability on the quote.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-26