Skip to main content
Unique Wood Products
Evenly spaced black square iron balusters set into oak treads and rising to an oak handrail, two per tread
Stair Code Library · Guards

How far apart can balusters be?

No opening in a required guard may allow a 4″ sphere to pass — from the walking surface to the top of the guard. Two stair exceptions apply: the triangle formed by the tread, the riser and the bottom rail may pass a 6″ sphere but not larger, and openings in the guard along the open side of a stair may pass a 4⅜″ sphere. The IBC uses the same limits, with 4⅜″ allowed anywhere between 36″ and 42″ of guard height. The rule sets the clear gap between balusters, not their centres; the centre spacing is the gap plus one baluster width.

Reflects 2021 IRC · 2021 IBC · ICC A117.1 · 2010 ADA · 2012 TAS. Adoption is local and amended — confirm the edition your authority having jurisdiction has adopted.

Guards
4″ sphere
Stair triangle
6″ sphere
Along the rake
4⅜″ sphere
Open risers
4″ sphere over 30″ of rise
The rule

The 4-Inch Sphere Rule

No opening in a required guard may allow a 4″ sphere to pass — from the walking surface to the top of the guard. Two stair exceptions apply: the triangle formed by the tread, the riser and the bottom rail may pass a 6″ sphere but not larger, and openings in the guard along the open side of a stair may pass a 4⅜″ sphere. The IBC uses the same limits, with 4⅜″ allowed anywhere between 36″ and 42″ of guard height. The rule sets the clear gap between balusters, not their centres; the centre spacing is the gap plus one baluster width.

Residential, commercial and accessible

ItemResidential · IRCCommercial · IBCAccessible · A117.1 / ADA / TAS
Guard openings4″ sphere4″ sphere up to 36″; 4⅜″ from 36″ to 42″—
Open side of a stair4⅜″ sphere4″, 4⅜″ above 36″—
Tread / riser / bottom-rail triangle6″ sphere6″ sphere—
Between open-riser treads4″ sphere where the flight rises more than 30″4″ sphereOpen risers not permitted

Where it is measured

PLAN · CUT THROUGH THE BALUSTERS↑ open side · the dropwalking side ↓clear 3-7/8″4″

A 3-7/8″ opening stops the 4″ sphere. IRC R312.1.3.On 1-1/4″ square balusters that is 5-1/8″ on centre.

Passes
Landing guard4″ sphere, from the floor to the top of the guard4″clear < 4″centres 4½″ · ½″ iron36″ · R312.1.2R312.1.3 · IBC 1015.4 — same 4″ sphere; 4⅜″ from 36″ to 42″ under the IBCGuard on the rake4⅜″ between balusters · 6″ in the tread triangle6″4⅜″tread · riser · bottom railtriangle: 6″ sphereR312.1.3 exc. 1Open riser4″ sphere over 30″ of rise · R311.7.5.14″
The sphere is the test, not the centre spacing. Balusters are laid out so the clear opening is under 4″; the triangle at the tread gets 6″; the rake gets 4⅜″. Open risers reject the 4″ sphere over 30″ of rise.

Gap, not centres

The rule limits the clear opening. Maximum centre-to-centre spacing is therefore 4″ plus the width of one baluster: 4½″ for ½″ square iron, 5¼″ for 1¼″ square wood, 5¾″ for a 1¾″ turned baluster measured at its narrowest turning. Set the field spacing ⅛″ tighter than the maximum to absorb layout drift, and lay out from the centre of the run so the end gaps at the newels match and neither exceeds 4″.

On the rake

Along a stair the opening between balusters is measured perpendicular to the rail, not horizontally, and the IRC allows a 4⅜″ sphere there. The perpendicular gap between two balusters at the same centres is smaller than the horizontal gap by the cosine of the stair angle, so a spacing that passes 4″ on the level passes on the rake without change. The one shape the rake adds is the triangle at each tread, between the tread, the riser above and the bottom rail or the first baluster: it may pass a 6″ sphere, which is why a shoe rail or a bottom rail does not have to sit hard on the tread.

Under the IBC

The IBC applies 4″ from the walking surface to the guard height and then allows 4⅜″ in the band from 36″ to 42″, so a 42″ commercial guard laid out at 4″ centres throughout complies without further thought. The 6″ triangle exception is the same. Industrial occupancies and equipment platforms get a 21″ limit, which is where cable and horizontal-rail guards come from and is outside this library.

Cited

The sections, as the tables carry them

These rows are the same rows the full residential and commercial tables show, filtered to this rule. Change one there and it changes here.

Stair geometry

  • Open risersR311.7.5.1

    Permitted, but where the flight rises more than 30″ the opening between treads must not pass a 4″ sphere.

Guards

  • OpeningsR312.1.3

    Must not pass a 4″ sphere.

    Baluster centers ≈ 4″ + one baluster width. The UWP baluster guides carry the spacing math.

  • Openings — stair triangleR312.1.3 exc. 1

    The triangle formed by tread, riser and guard bottom rail may not pass a 6″ sphere.

  • Openings — open side of stairsR312.1.3 exc. 2

    Guards on the open side of a stair may not pass a 4-3/8″ sphere.

Guards

  • Openings below 36″1015.4

    Must not pass a 4″ sphere.

  • Openings 36″ to 42″1015.4 exc. 1

    Must not pass a 4-3/8″ sphere.

  • Stair triangle1015.4 exc. 2

    The tread / riser / bottom-rail triangle may not pass a 6″ sphere.

In hardwood

How the rule is met with the part

The Baluster Spacing Calculator takes a rail length between newels and a baluster width and returns the count, the centres and the end gaps that pass the 4″ sphere. Two ½″ iron balusters per tread on a 10″–11″ run gives 5″–5½″ centres and a 4½″–5″ gap, which fails; the correct count on an 11″ tread is two balusters at 4⅜″ centres with a third on every other tread, or ⅝″ or ¾″ stock at two per tread — the calculator shows both. Wood balusters are plowed into the rail with the 6006 fillet between them, so the spacing is set at the fillet lengths.

What fails inspection

  1. 01

    Setting balusters at 4″ on centre and thinking the rule is met with margin. It is — but it was 4″ clear that was required, and 4½″ on centre for ½″ iron was available.

  2. 02

    Setting balusters at 5″ centres for ½″ iron because two per 10″ tread looked right. The gap is 4½″.

  3. 03

    A bottom rail on a stair set so the triangle at the tread passes a 6″ sphere — usually a shoe rail raised on blocks.

Questions on this rule

What is the maximum spacing for stair balusters?
A clear opening under 4″. For ½″ square iron that is 4½″ on centre; for 1¼″ square wood 5¼″. Set the field slightly tighter.
Does the 4-inch rule apply on the stair as well as the landing?
Yes, with a 4⅜″ allowance along the rake under the IRC and a 6″ allowance at the tread triangle. In practice the landing spacing is used on the stair as well.
How many iron balusters per tread?
Two on a 10″ run with ½″ stock gives a 4½″ gap and fails; use three per tread, two per tread of ¾″ stock, or a pattern of two and three. The calculator settles it for the actual run.
Check it against the part

Send the section. We answer with the part that meets it.

Riser, tread, nosing radius, rail perimeter, extension length — send the stair section and the adopted code year and the shop drawing comes back with each one called out.

Terms used on this page