Skip to main content
Unique Wood Products

Why is a 1×6 not actually six inches wide?

Nominal size is the rough dimension before surfacing; actual size is what you get after the planer. A 1×6 leaves the mill rough at roughly one inch by six and arrives S4S at 3/4 inch by 5-1/2 inch. Hardwood adds a second system: quarters, where 4/4 is one inch rough and 8/4 is two inches rough.

The short version

  • Nominal = rough. Actual = surfaced. The name never changes; the board does.
  • Softwood-style naming: 1×4 is 3/4″ × 3-1/2″, 1×6 is 3/4″ × 5-1/2″, 1×8 is 3/4″ × 7-1/4″, 1×12 is 3/4″ × 11-1/4″.
  • Hardwood quarters: 4/4 is 1″ rough and surfaces to about 13/16″ or 3/4″; 5/4 surfaces to about 1-1/16″; 8/4 surfaces to about 1-3/4″.
  • Board feet are figured on the rough dimension, which is why the maths looks generous next to what you can measure.
  • Layout is where it bites: four "6-inch" boards cover 22″, not 24″.

The full answer

Two things are going on, and mixing them up is where the confusion starts. The first is surfacing: a board is named at the size it was cut green and rough, and it keeps that name after the planer takes material off every face. The second is that hardwood and construction lumber use different naming systems entirely.

The board-name chart

CalledActual, surfacedFour of them cover
1×23/4″ × 1-1/2″6″
1×43/4″ × 3-1/2″14″
1×63/4″ × 5-1/2″22″
1×83/4″ × 7-1/4″29″
1×103/4″ × 9-1/4″37″
1×123/4″ × 11-1/4″45″

Note the jump at 1×8. Boards up to 1×6 lose half an inch of width; from 1×8 up they lose three quarters. There is no rule of thumb that covers both, which is why the chart is worth keeping rather than the arithmetic.

Hardwood quarters

Hardwood is sold in quarter-inches of rough thickness, written as a fraction over four. 4/4 ("four quarter") is one inch rough. 8/4 is two inches rough. The system exists because hardwood is sawn to thickness and sold by volume, while width is whatever the log gave — hardwood boards come in random widths, not standard ones.

CalledRough thicknessTypical surfaced thickness
4/41″13/16″, or 3/4″ for trim stock
5/41-1/4″about 1-1/16″
6/41-1/2″about 1-5/16″
8/42″about 1-3/4″

Surfaced thicknesses vary slightly by mill and by what the board allowed — a cupped 4/4 board loses more to get flat. If a thickness is critical to a joint, name it on the quote rather than assuming the standard. UWP surfaces in-house, so a specific finished thickness is a scheduling question, not a sourcing one.

The two places this costs money

  • Layout. Cladding a 24″ space with "6-inch" boards takes four boards and leaves a 2″ strip. Plan from the actual width every time — and on shiplap and tongue and groove, plan from the coverage width, which is smaller again once the lap or the tongue is hidden.
  • Pricing. A board foot is 144 cubic inches figured on rough thickness and width. An 8-foot 4/4 board that is 6″ rough is 4 board feet, even though you can only measure 3/4″ × 5-1/2″ when it arrives. That is the convention, not a markup.

One more that catches people out on stair and trim work: riser stock, skirt boards and wide shelving are often specified by nominal width out of habit. A 1×12 skirt is 11-1/4″, which is fine until a rise-and-run layout assumed a full 12″ of coverage above the tread. Measure the board, not the name.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-09-14