Skip to main content
Unique Wood Products

What is a stair skirt board, and do I need to replace mine?

A stair skirt board is the flat trim piece running along the wall beside a staircase. It covers the rough edges of the stringers and treads where they meet the wall. On most carpeted stairs built since the 1960s, the skirt is a nominal 1×8 (about 11/16″ thick) — the critical reference dimension for retro-fit tread installs. Keep the skirt if it’s clean; replace if you’re changing tread thickness.

The short version

  • The skirt board is the flat trim running along the wall alongside the stair. It covers the rough side of every tread and riser where they meet the wall, plus the top edge of the stringer.
  • Standard thickness: about 11/16″ on most carpeted stairs (nominal 1×8 lumber). This is the reference dimension that determines whether a retro-fit tread will land flush.
  • Keep it when the skirt is intact, paint-grade, and you’re installing 8071 / 8073 retro-fit treads — they land flush.
  • Replace it when you’re changing tread thickness (1″ full treads onto a previously carpeted stair), upgrading the look, or the skirt is damaged.

The full answer

The skirt board is one of the most underrated pieces of trim in a house — it does practical work, controls the aesthetic of the stair, and determines whether your retro-fit tread install will look finished or look unfinished. Most homeowners have never named it; every installer cares about it.

What it is

The skirt board is the flat trim board running along the wall beside the stair, from the bottom of the stair up to the top. It covers the rough edges where every tread and riser meet the wall, plus the top edge of the stair stringer (the diagonal structural framing). The skirt is what makes the stair look like a finished piece of architecture, rather than a row of exposed boards sticking into a wall.

Stairs with two finished sides (against walls on both sides) have a skirt on each side. Stairs with one open side typically have a skirt on the wall side and a stringer with bullnose returns on the open side instead.

Why thickness matters for retrofits

On almost every carpeted stair built in the last 50 years, the skirt is nominal 1×8 lumber, actually about 11/16″ thick. The skirt was sized to match the combined height of the carpet and pad — so the top of the carpet sat flush with the top of the skirt, and the install looked finished.

When you pull up the carpet, the skirt is suddenly standing 11/16″ proud of the bare substrate. That 11/16″ is the reference dimension you need to hit with your new wood tread:

  • 8071 / 8073 retro-fit tread (5/8″ body + 1/16″ glue ≈ 11/16″) lands flush with the skirt.
  • 8070 / 8072 full tread (1″ body) sits about 5/16″ proud of the skirt — visible step where the tread meets the wall, reads as unfinished.

This is why the 8071 exists. The skirt-board math drives the retrofit product line.

When to keep your existing skirt

  • You’re installing 8071 / 8073 retro-fit treads and the skirt is clean — leave it. Retreat the skirt with primer and paint, it’s ready.
  • The skirt is paint-grade poplar or pine and you’re re-painting anyway — fill nail holes, sand, repaint. Quick refresh.
  • You’re only redoing the carpet runner without changing the tread surface — skirt stays.

When to replace the skirt

  • Changing tread thickness. Going from 8071 retrofit to 8070 full tread, or going from full hardwood treads to a different tread thickness — replace the skirt so the math lines up.
  • Going from paint-grade to stain-grade. Existing skirts are usually poplar or pine (paint-grade). If you want a stained hardwood skirt to match new hardwood treads — replace.
  • Damaged, water-stained, gouged, or pieced-together skirt. A skirt with a lot of damage usually can’t be cleanly refinished. Replace.
  • Adding a substantial new baseboard at the bottom of the stair. The skirt and baseboard need to meet cleanly; replacing both is easier than scribing into an existing skirt.

How to install a new skirt

On a renovation, the skirt is typically installed before the treads — fit it tight against the wall, scribe the bottom edge to follow the diagonal of the stair, then drop the treads into the resulting pocket. On a new build, the rough stringer goes in first, then the skirt over the stringer, then treads and risers.

UWP doesn’t stock pre-cut skirt boards (every stair is a different geometry), but we mill skirt stock to length in any of our six stain-grade species or poplar. Provide your stair’s total rise, total run, and tread/riser count, and we can mill matching skirts. Most finish carpenters cut the diagonal on-site after fitting.

Stringer vs. skirt — the difference

Some terminology gets mixed: the stringer is the structural framing of the stair — the diagonal 2× lumber that the treads and risers attach to. The skirt is the trim that covers the side of the stringer where it meets the wall. On a closed-stringer stair (with a wall on both sides), both stringers are hidden behind skirts. On an open-stringer stair (one side visible), the structural stringer is itself a finished piece and there’s no skirt on that side.

At a glance

SituationSkirt decision
8071 retrofit, existing skirt intactKeep — paint over, ready to install.
8070 full tread retrofit, carpeted stairReplace (or accept the tread sitting 5/16″ proud).
Going from paint-grade to stain-gradeReplace in matching species.
Existing skirt damaged or piecedReplace.
Brand new constructionInstall fresh — material choice is open.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-27