Skip to main content
Unique Wood Products

8071 Retro-Fit Bullnose Stair Tread

A renovation overlay tread — a 5/8" solid hardwood body with a built-up full 1" bullnose nose that caps an existing stair without tearing it out. Edge-glued, never veneered, milled in-house from US domestic hardwood in Red Oak and White Oak.

  • Spec sheet PDF
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Availability
Core catalogTanner Rd, NW Houston
Lead time
Confirmed at quote
Price
From $8442″ × 11-1/2″ red oak, no returns · price your exact size
Sample
Order a sampleHold it before you order

Product views

Section · 8071

The true section — depth across, thickness down, nose at the right. The same closed outline the model above is swept from.

Depth
11 1/2"
Thickness
1"
Body
5/8"
Nose
Full bullnose

Profile

5/8" body · 1" nose

  • Retro-Fit Bullnose
  • 5/8" + built-up 1" nose
  • Red Oak · White Oak
  • Tanner Rd Yard

Species

Shown as an indication of colour, not a figure sample. Grain and colour vary board to board.

Width & end treatment

Reddish tone, prominent open grain. The standard match for red oak stairs and the most-stocked retro-fit species. Stocked in both species. The most common retro-fit width.

Profile
Retro-Fit Bullnose
Thickness
5/8" body
Depth
11-1/2"
Nose
Built-up bullnose
Category
Retro-Fit Treads
Species
Red Oak · White Oak
Sold by
The piece
SUBMITTAL DOCUMENTSDrawn for 8071RO48

Sheets are marked preliminary. UWP confirms availability, species and lead time before release.

Need a non-stock species, a curved stair, or a length we don't stock? Our mill custom-runs and templates to spec — see Custom Stair Treads.

Order number

8071RO48

UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
Where a retro-fit tread goes

Cap the tread
that is already there.

A retro-fit tread is a renovation overlay. The 5/8" body sits on the existing tread and a built-up 1" bullnose wraps its front edge — so a carpeted or worn stair gets solid hardwood without pulling a single tread.

  1. Trim the old nose flush

    Cut the existing bullnose back to the riser face. The overlay needs a square front to wrap.

  2. Measure the old tread

    Length skirt to skirt. Depth from the riser above to the trimmed face — usually 10-1/4". The overlay adds 1-1/4" of nose, which is why the stocked size is 11-1/2".

  3. Glue, fasten, done

    The body lands flat on the old tread, the lip drops over its face, and the riser below can be capped to match. No demolition, no re-stringing.

  4. Open side? Return the end

    On an open-side stair the overlay runs 1-1/4" past the stringer and a returned end wraps the nose around the corner. The L-shape body is handed, so specify left or right.

How a retro-fit tread caps an existing stair, and how to measure for oneSection through two steps of an existing stair. Each old tread has its nose trimmed flush with the riser; a 5/8 inch hardwood overlay sits on top with a built-up 1 inch nose that wraps the front. A plan view below shows the length measured skirt to skirt and the depth from the riser to the trimmed face, plus 1-1/4 inch for the nose.SECTION · OVERLAY ON THE EXISTING STAIROld nose trimmed flush; 5/8" body on top, 1" bullnose caps the front.11-1/2" overlayexisting 10-1/4" + 1-1/4" nose1"nose1-1/4" nose lip5/8"bodyriserexisting treadold nosetrimmed flushDrawn to scale · existing 1" tread, nose trimmed flush · 5/8" body · 1-1/4" nose runPLAN · MEASURING THE EXISTING TREADLength skirt to skirt; depth from the riser to the trimmed front face.wallexisting tread · nose trimmed48" · length along the nose10-1/4"existing11-1/2"overlayTrim the old nose flush with the riser, then measure riser to face — usually 10-1/4".Overlay depth = existing depth + 1-1/4" nose. That is why the stocked size is 11-1/2".Length: skirt to skirt, same as the old tread. Other depths are cut to order.THE RETURNED END · OPEN STAIRCASEOne side of the stair meets a wall; the other is open, so that end shows.The returned end wraps the nose round the open end so no raw board end shows.1 · FROM ABOVEWALL SIDEclosed endcut square,butts the skirtBACKsits against the riser — the upright board of the step aboveFRONT · THE NOSEthe rounded edge you step overoutside face of the stringer(the board the treads sit on)1-1/4"OPEN SIDEno wall — you can seethis end of every stepreturned enda 1-1/4" piece with the samenose, fixed to the end so thenose turns the corner andthe raw board end is hidden.It runs 1-1/4" past the back,behind the riser above.2 · STANDING BESIDE THE OPEN SIDEThe same tread seen from the room, looking at its open end.FRONT · THE NOSE← the tread carries on to the wall sideBACK · against the riserOPEN SIDEthe returned endthe same nose, wrappedround the corner — no rawend of the board showingMeasure: wall to the outside face of the open stringer, plus the 1-1/4" returned end.Not reversible: it has a top and a bottom — tell us which side is open.Returned retro-fit treads are cut to order — specify the open side.
Top: section through an existing stair — old nose trimmed flush, 5/8" overlay body on top, 1" nose wrapping the front. Middle: the existing tread in plan, measured skirt to skirt and riser to trimmed face. Bottom: the returned end on an open staircase.
Risers · the upright board

The board you see,
not the one you step on.

A riser is the upright board that closes each step, standing between one tread and the next. On a retro-fit, a thin primed riser caps the existing riser the same way the overlay tread caps the old tread — the nose of the new tread hides its top edge. Every step has one, and a flight has one more rise than it has treads.

  1. Pick painted or stained

    Most staircases run a painted white riser under a stained tread — that is the primed 1/2" piece. For a riser in the same wood as the tread, use 3/4" hardwood S4S from the yard in Red Oak, White Oak, Maple or Hickory and stain it with the treads.

  2. Measure the rise

    Top of one tread to the top of the next, on three steps of the flight. Stock is 7-1/2" tall, which is more than any residential rise leaves showing once the tread sits on it, so the riser is ripped down to fit on site — never built up.

  3. Measure the width

    Wall to wall across the step, at the back where the riser sits. On an open side, to the finished face of the stringer. Measure every step; old stairs wander.

  4. Count the rises, not the treads

    A flight has one more rise than treads. Each 90" primed piece cuts into 2 risers for any stair up to 44" wide; wider than that, count one piece per rise. Hardwood S4S comes in random lengths — give us the count and the width and the yard pulls boards to yield it.

  5. Set it before the tread

    Cap the old riser first, then set the overlay tread so its 1-1/4" nose lands over the new riser's top edge. Cove or bull nosing from the stair-moulding line covers the joint below.

THE RISER · SECTION THROUGH A RETRO-FIT STEPSeen from the side. A thin primed riser caps the old riser; the new nose lip hides its top.stringerold riserold tread, nose cut flushoverlay belowTHE RISERprimed, over the old onetucked under the nose lip1/2"primed · 3/4" hardwood also fitsretro-fit tread on top1-1/4"nose lip over the old faceTHE RISEtread top to tread topwhat your tape readsTHE PRIMED PIECE · 1/2" × 7-1/2" × 90"riser 1riser 2one cut90" long7-1/2" tallTwo risers per piece for any stair up to 44" wide. Wider than that, one riser per piece.
Two ways to buy a riser
Primed white riserHardwood S4S riser
Size1/2" thick × 7-1/2" tall3/4" thick × 7-1/2" tall
Length90" long — usually two standard risers per pieceRandom lengths as the yard has them — cut to the width of each step on site
SpeciesPaint-grade, primed whiteRed Oak · White Oak · Maple · Hickory
FinishReady for your topcoatUnfinished, surfaced four sides — stain to match the treads
Sold asBy the 90" pieceBy the board, from the yard
Best forThe classic painted riser under a stained tread — and the retro-fit overlay, thin enough to cap an existing riser without moving the nose.A stained riser that matches the tread species, or a painted riser in solid wood on a new build.

Hardwood S4S lengths and species on hand are the yard's day-to-day stock — confirmed at quote. See hardwood S4S & S3S for the dimension-stock program.

Worked count

A straight flight of 12 treads has 13 rises — one more than the treads, because the first rise is from the floor to the first tread and the last is up onto the landing. On a stair 42" wide, each primed piece cuts into 2, so order 7 primed pieces. In hardwood S4S, tell us 13 risers at 42" and the yard pulls the boards to yield it.

Top: section through a retro-fit step — a 1/2" primed riser over the old riser, the overlay tread's nose hiding its top edge, the rise dimensioned tread top to tread top. Below: the 90" primed piece cut into two risers.
Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the new stair disappears into the room.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Core catalog
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Core catalog
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Specifications

The full spec sheet. For the builder who scrolled this far.

Body5/8" solid
NoseBuilt-up full 1" bullnose
Depth11-1/2"
Width42" · 48"
ConstructionEdge-glued solid — never veneered
Stocked speciesRed Oak · White Oak
SurfaceUnfinished, sanded
UseOverlay on existing stairs
Lead timeConfirmed at quote
Minimum order1 piece
OriginUS domestic hardwood · milled in-house
Custom runsAny species, length, template
Popular wood species

The species we run most.

Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.

Red Oak
Core catalog
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Core catalog
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Why the 8071

Re-tread a stair
without tearing it out.

The 5/8" body keeps the new surface low enough to lap over an existing tread, while the built-up 1" bullnose nose gives a full, finished step edge.

  • Carpet-to-wood remodels

    Pull the carpet, cap the existing treads — a solid hardwood stair without rebuilding the carriage.

  • Tired-tread refresh

    Worn or paint-locked treads get a new solid hardwood surface that lands flush with minimal rise change.

  • Occupied-home jobs

    Less demolition, dust, and downtime than a full tread replacement — practical for lived-in stairs.

  • Matched stair systems

    Species-matched to retro-fit risers and nosing for a cohesive overlay staircase.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

What is a retro-fit tread?
An overlay: a 5/8" solid hardwood body with a built-up full 1" bullnose nose. It caps an existing stair tread so you get a solid wood stair without removing the old treads or rebuilding the carriage.
Why is the body 5/8" but the nose 1"?
The thin 5/8" body keeps the finished surface low enough to lap over the existing tread without a big rise change; the nose is built up to a full 1" bullnose so the step edge still looks and feels like a solid tread.
Are these solid wood or veneered?
Solid hardwood, edge-glued — never veneered.
Which species and sizes are stocked?
Current material availability, production timing, pickup, and delivery are confirmed on the written quote after UWP reviews the exact SKU, species, quantity, geometry, and shop capacity.
Do you show pricing here?
Not on this reference page. Pricing is returned instantly in the Custom Retro-Fit configurator for your exact species, size, and quantity.
Pickup or delivery?
Current material availability, production timing, pickup, and delivery are confirmed on the written quote after UWP reviews the exact SKU, species, quantity, geometry, and shop capacity.
All answers →