
PoplarPaint-Grade · Most Popular
Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.
1-1/4" × 2-1/4" — milled to order at NW Houston / Tanner Rd in Primed FJ Pine, Red Oak, White Oak, Maple, Pine, Knotty Alder, Primed MDF, Flex, or ground to match an existing profile.
Primed FJ Pine · 1-1/4" × 2-1/4"
T-Astragal · Full-length stick
PROFILE
UW1310
priced by the piece on your quote
The UW1310 t-astragal profile in 1-1/4" × 2-1/4" — run to order in solid hardwoods, paint-grade primed, and MDF.
T-Astragal · Special order · Custom milling available
Colour is indicative — grain and colour vary board to board.
A stocked profile runs one size off one knife. Length is a quantity, not a dimension — order by the piece.
Need this section at another height, in another species, or ground to match an existing profile? That is a custom run — send us a sample or an offcut.
Order by the code above at the Tanner Rd counter. Pricing, availability and lead time are confirmed on the quote.
PROFILE
UW1310priced by the piece on your quote
Specification · UW1310
Primed FJ Pine · 1-1/4" × 2-1/4" · T-Astragal
Stocked profiles run primed for paint; in solid wood this one is milled to order, so the species is your choice rather than whatever is on the shelf. These are the five we run most for t-astragal — pick one in the swatches above to see this profile in it.

Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.

Best for — The workhorse match for red oak floors — the most-stocked species across treads and moulding.

Best for — Cooler, modern, wire-brushed and natural finishes; the premium choice for light contemporary work.

Best for — Pale contemporary work, maple cabinetry, and anywhere an even near-white tone is wanted.

Best for — Dark, high-end interiors and feature work where a rich chocolate tone is the statement.
A finished t-astragal profile for trim, panel, and millwork detailing.
Primed FJ pine and MDF for paint; solid Red/White Oak, Maple, Pine, and Knotty Alder for stain.
Coordinates with matching base, casing, and crown for a consistent millwork program.
Match an existing profile or run a custom length — our mill cuts to spec.
Nominal size is the rough dimension before surfacing; actual size is what you get after the planer. A 1×6 leaves the mill rough at roughly one inch by six and arrives S4S at 3/4 inch by 5-1/2 inch. Hardwood adds a second system: quarters, where 4/4 is one inch rough and 8/4 is two inches rough.
Read the answer →Paint-grade stock is chosen for a flat, even surface that disappears under primer — grain, colour and small defects do not matter because nothing will show. Stain-grade stock is chosen for its face: colour, figure and grain continuity across a run. Poplar is the paint-grade default because it machines cleanly, holds a crisp profile edge and takes primer well.
Read the answer →A big-box store stocks one or two species of stair tread, a handful of generic moulding profiles, and almost no custom capability. A real mill carries six species, mills custom profiles to match existing trim, runs short orders without minimums, and has people on the phone who actually know the material. The cost difference is usually less than people expect; the expertise gap is enormous.
Read the answer →Yes. UWP runs custom knives to match existing baseboards, crown, casing, and any other milled profile. Bring us a 6-inch sample piece, a clean sketch with dimensions, or even a photo with a scale reference. We grind a new knife to match, run your order, and keep the knife on file for re-orders. One-time knife fee covers the setup; per-foot pricing matches our stock catalog.
Read the answer →