Skip to main content
Unique Wood Products

Can you match my existing moulding profile?

Yes. UWP runs custom knives to match existing baseboards, crown, casing, and any other milled profile. Bring us a 6-inch sample piece, a clean sketch with dimensions, or even a photo with a scale reference. We grind a new knife to match, run your order, and keep the knife on file for re-orders. One-time knife fee covers the setup; per-foot pricing matches our stock catalog.

The short version

  • Yes — we mill custom matches to any baseboard, crown, casing, chair rail, panel mould, or one-off profile.
  • Best to bring: a 6-inch piece of the original moulding. Failing that: a clean end-grain sketch with dimensions, or a high-resolution photo against a ruler.
  • The fee: a one-time knife grinding charge covers the new tooling. Per-foot pricing then matches the stock catalog for the same species and width band.
  • Timing: confirmed on the written quote. A new knife is designed, ground and proofed before the run is scheduled. We keep the knife on file — re-orders skip the knife fee.

The full answer

If you’re remodeling part of an older home, adding on, or replacing damaged trim, the trim you need probably doesn’t exist on any current stocked-profile chart. The original mill is closed, the profile was a one-off from a 1970s housing tract, or it’s a custom run from a previous owner’s remodel. UWP grinds custom knives to match. This is one of the things a real mill does that no online retailer or big-box store can.

How custom matching actually works

A moulding profile is shaped by a steel knife mounted in a moulder head. The knife is the negative of the profile you see — when stock wood passes over a spinning head, the knife carves the profile into the face. To match an existing moulding, we grind a new knife that matches its cross-section, mount it in the moulder, and run your order through.

The knife itself is the work. Once it exists, the per-foot price of the stock matches our standard catalog pricing for the same species and width band. We keep the knife on file under your name; re-orders skip the knife fee entirely, even years later.

What we need from you

In order of best to workable:

  • A 6-inch (or longer) sample piece of the original moulding. This is the gold standard. Pull a short scrap from a closet, an attic, or behind a baseboard return. The shop scans or measures the cross-section directly. No drawing needed.
  • An end-grain sketch with real dimensions. Cut a clean cross-section off your sample, photograph the end straight-on against a ruler, and mark the key dimensions (overall width, overall height, key feature radii or angles). We can grind from this.
  • A high-resolution photo with a scale reference. Hold a tape measure or ruler flat against the end of the moulding and shoot straight-on. This is workable if a sample really can’t be pulled — but accuracy is lower; expect one round of revision.
  • A vendor SKU or pattern number if you know the original mill. We can sometimes look up an existing knife pattern from industry references.

Bring the sample to the Tanner Rd yard in person, or mail it to us — addressed to UWP, 9915 Tanner Road, Houston, TX 77041, Attn: Custom Knife. Samples are returned with your order.

What the knife fee covers

The fee is one-time and per profile. It covers:

  • Cross-section analysis and CAD drawing of the new knife.
  • Grinding the steel knife blank to the new profile.
  • Setup and first-article run on the moulder.
  • Permanent storage of the knife in our tooling library, indexed to your account.

Once the knife exists, re-orders skip the fee entirely. Trim a closet ten years from now? Same knife, no knife fee, stock pricing.

Species and dimensional limits

We run custom knives in all stocked species — poplar (paint-grade), and red oak, white oak, hickory, hard maple, walnut, and brazilian cherry for stain-grade. Profile size is limited by the moulder capacity; we can mill profiles up to roughly 8 inches wide and 1¼ inches thick in one pass. Anything larger may need a stacked or built-up assembly — still doable, just a different program.

Production timing

A new knife requires design, grinding, and proofing before the run can be scheduled. Quantity, species, tooling complexity, and current shop capacity determine production timing. If a remodel depends on matched trim, start the knife conversation early and use the confirmed quote schedule as the project baseline.

When matching isn’t worth it

Sometimes the honest answer is don’t match. If you’re re-doing the whole house anyway, the original trim was never great, or the existing profile is one feature you’ve been wanting to update — switch to a stocked profile and re-trim the rooms that change. The knife fee is only worth it when keeping the existing look is the goal. Ask, and we’ll tell you when it isn’t.

How to start

Pull a sample, take a photo of the end with a ruler against it, or sketch the cross-section with dimensions. Email it to the mill or bring it to the Tanner Rd yard at 9915 Tanner Road. We come back with a knife-fee quote and a timeline.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-27