Panel Mould · by face height
2-1/4″ Panel Mould
33 profiles · 33 milled to order
Panel mould is sized to the panel: 1″ to 1-1/2″ for a wainscot under 36″, 1-3/4″ to 2-1/2″ for full-height panels and coffers.
33 panel mould profiles are offered at 2-1/4″ and 33 milled to order from the knife library. Library profiles come from one knife at several heights, so a 2-1/4″ run can step up or down a size elsewhere in the house and still mitre together.
Other panel mould profiles

Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-15/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.728"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 15/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-5/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.926"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.797"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-1/8"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-7/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.59"
Milled to orderView profile →
Panel Mould
2-1/4" × 3/4"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-9/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-1/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-3/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.662"
Milled to orderView profile →
Panel Mould
2-1/4" × 1.543"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.905"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-3/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-1/4"
Milled to orderView profile →
Panel Mould
2-1/4" × 11/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 0.844"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-3/8"
Milled to orderView profile →
Panel Mould
2-1/4" × 1-1/8"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 13/16"
Milled to orderView profile →
Panel Mould
2-1/4" × 1.285"
Milled to orderView profile →Terms used on this page
Questions people ask before ordering
Wainscoting styles — beadboard, shiplap, board-and-batten, raised panel. Which one for my room?
Wainscoting is wall paneling that covers the lower 30 to 48 inches of a wall. Five main styles: beadboard (narrow vertical strips with bead detail), shiplap (horizontal overlapping boards), board-and-batten (flat panels with vertical battens), flat-panel (simple recessed squares), and raised-panel (formal beveled panels). Pick on home style — beadboard for farmhouse, shiplap for coastal, raised panel for traditional formal.
Read the answer →What trim goes where? A room-by-room guide.
Trim choice should read as a consistent system across the house, not a room-by-room patchwork. Baseboard and casing run everywhere, sized to ceiling height and door scale. Crown is reserved for formal rooms in traditional homes and skipped in modern ones. Chair rail and panel mould go in formal dining and entry. Stair trim ties the upstairs and downstairs together.
Read the answer →Crown vs. cove moulding — what’s the difference and which one do I need?
Crown moulding is sprung — it sits at an angle bridging the wall and ceiling, with an ornate profile that can include curves, beads, and steps. Cove moulding is a single concave curve, sitting flat into the wall-ceiling corner. Crown reads as traditional and substantial; cove reads as clean and quieter. For 8-foot ceilings, cove or small crown. For 9-foot+, scale up.
Read the answer →Can you match my existing moulding profile?
Yes. UWP runs custom knives to match existing baseboards, crown, casing, and any other milled profile. Bring us a 6-inch sample piece, a clean sketch with dimensions, or even a photo with a scale reference. We grind a new knife to match, run your order, and keep the knife on file for re-orders. One-time knife fee covers the setup; per-foot pricing matches our stock catalog.
Read the answer →

