Skip to main content
Unique Wood Products
For architectural millwork shops · Milled in Houston since 1988

The moulding run behind your millwork package.

Send the section. We grind the knife, run it in your species, and put it on a pallet. Matched, custom, and stock hardwood mouldings, S4S dimension stock, and stair parts for the shops that fabricate hotels, clubs, and estates — and never a bid against the shop we supply.

Read the commercial brochure 8 pages · PDF · 1.9 MB
A formal dining room with a deep layered oak cornice over painted framed wall panels, tall oak window casing and a herringbone oak floor in low afternoon light
Wainscot · Pilaster · Casing · Cornice · BaseSolid hardwood lineal profile · Division 06 40 00
Knives ground in-house
From your drawing, sample, or photo
Solid hardwood, kiln dried
Run in the species your spec calls for
One supplier, one PO
Mouldings, S4S stock, stair parts
Will-call or metro delivery
Staged to your PO at Tanner Rd
Why shops outsource the run

Your moulder is the bottleneck. Ours is not.

A hospitality package carries thousands of lineal feet of casing, base, crown, and panel mould that your shop has to run before a single elevation goes to the bench. Every hour on the moulder is an hour off CNC, veneer, and finishing — and every knife change is an hour nobody billed. UWP runs the lineal footage so your floor stays on the work that carries margin.

A length of freshly profiled oak casing coming off a moulder outfeed between steel rollers, the bead and cove crisp along its edge

Profile matching

Bring the architect’s detail, a cut-off from the existing house, or a photo with a rule in frame. We grind a knife to match and send a sample stick for approval before the run.

Custom profiles

Designer-drawn cornice, casing, and panel mould in the species on the finish schedule. Solid hardwood, never veneered.

Stock profiles, ready now

Baseboard, casing, crown, cove, chair rail, panel mould, shoe, quarter round, and flooring transitions on the shelf at the NW Houston / Tanner Rd mill.

S4S and S3S dimension stock

Surfaced hardwood boards and trim stock, sized for your shop so the panel and rail work starts from square.

The section, in CAD

The profile you draw is the profile we grind.

These are the milled sections themselves — traced from the catalogue’s own drawn cross-sections and scaled to the profile’s stated dimensions, which is the same geometry the 3D viewer sweeps. Every stocked profile carrying one downloads as a DXF for your CAD and as an ANSI-A dimensioned shop drawing for the submittal, so your detailer draws the part that actually arrives on the pallet.

159
Stocked profiles at the Tanner Rd mill
1,499
Profile styles in the semi-custom library
1988
Milling in NW Houston since
UW48Crown9/16" × 4-1/4"DXFShop drawingSpec
MC9Casing7/8" × 3-1/4"DXFShop drawingSpec
ACOL7601Baseboard9/16" × 3-1/4"DXFShop drawingSpec
CR6Chair rail1-1/4" × 3-1/2"DXFShop drawingSpec
KPANELPanel mould3/4" × 1-1/4"DXFShop drawingSpec
Browse every stocked section →Identify a profile from a photo →Drawn as milled, all five at one scale — girth across, thickness up. Sizes read thickness × girth.
How a shop buys from UWP

Drawing to pallet in five steps.

  1. A sample stick of oak crown moulding and a painted cut-off on a printed millwork detail sheet, with a contour gauge and calipers1

    Send the profile

    DWG, PDF, a sample stick, a cut-off, or a photo with a rule in frame. Add species, lineal footage, and the date the material is due at your dock.

  2. A material takeoff sheet and quote pages on a shop office desk, with an offcut of oak moulding used as a paperweight2

    Quote and lead time

    Priced against your account with a confirmed lead time. Houston-metro delivery, when you need it, is priced on the same sheet.

  3. Four steel moulder knife blanks ground to a cove, an ogee, a bead and a layered cornice profile, fanned out on a bench beside a brass template3

    Knife and sample

    The knife is ground in-house to the section. For custom or matched work a sample stick goes out for your approval before the run is scheduled.

  4. Milled lengths of oak moulding stacked in tagged bundles on a bench, a blank paper tag tied to the top bundle4

    The run

    Kiln-dried solid hardwood, run to the approved section, inspected off the moulder, bundled with separators and tagged to your PO.

  5. A crated bundle of long hardwood moulding on a pallet with corner protectors and banding straps beside an open roll-up door5

    Will-call or delivery

    Crated with corner protectors and banded, then staged for will-call at NW Houston / Tanner Rd or delivered to a Houston-metro shop or jobsite on the schedule set at quote.

Crafted in-house · Service-driven · Trade-proven

A trade-proven moulding source.

  • Knife ground in-house from your drawing
  • Sample stick approved before every custom run
  • Solid kiln-dried hardwood, never veneered
  • Species on the finish schedule, not a substitute
  • Confirmed lead time on the quote
  • Delivery priced on the quote, not after
  • Bundled and tagged to your PO
  • Match-to-existing from a cut-off
  • Mouldings, S4S stock, and stair parts on one PO
  • Never a bid against the shop we supply
  • No field crew — the install stays yours
  • Family-operated at NW Houston / Tanner Rd since 1988
Built for the submittal

Material your shop drawings can stand on.

Division 06 40 00 packages get reviewed by the architect, the general contractor, and on flagged hotels the procurement agent. The moulding behind those drawings has to be the species on the finish schedule, at the moisture content the spec calls for, in the profile the designer drew. Getting that right is the work, not the part of the order that fills a gap between other jobs.

Seven surfaced hardwood sample boards laid edge to edge — white oak, red oak, hard maple, hickory, walnut, alder and poplar
Surfaced samples in the hardwoods UWP runs — white oak, red oak, hard maple, hickory, walnut, alder and poplar. Others on request.
Species
White oak, red oak, hickory, maple, walnut, alder, and poplar, with others on request. Paint-grade in poplar or primed finger-jointed pine.
Profile fidelity
Knife ground to the section on the drawing. Sample stick approved by your shop before the run.
Moisture
Kiln-dried hardwood for interior millwork. Ask for the reading on the run.
Lengths and bundling
Random lengths by default. Specified lengths and per-elevation bundling on request.
Documentation
Section drawing, species, and PO tag on every bundle. DXF and ANSI-A sheets on the stocked sections; cut sheets on request for the submittal.
Match-to-existing
Restoration and renovation profiles matched from a cut-off. Common on club and hotel renovations.
Commercial custom millwork

The Division 06 package, cut to the drawing.

Beyond lineal profile, UWP fabricates the solid hardwood components that a commercial millwork package calls out by elevation: jambs, panels, mantels, wood countertops, curved stair systems, and radius platforms. Shop drawings are prepared for the submittal, and the material is cut, finished to your spec, and staged for will-call or Houston-metro delivery.

A hotel lobby bar front built as a run of raised walnut panels between pilasters, under a moulded cap and over a deep moulded plinth, with a brass foot rail
Hotels · Clubs · Restaurants

Public-space packages

Lobby paneling, bar fronts, reception surrounds, corridor casing and base. Profiles matched to the interior designer’s detail and bundled per elevation.

An institutional lobby with oak raised-panel wainscot, fluted pilasters at a cased opening and a deep layered cornice
Office · Institutional

Boardroom and lobby millwork

Solid hardwood panel mould, chair rail, crown, and jambs for corporate and institutional interiors. Submittal cut sheets on request.

A two-tier curved platform in rift white oak at the front of a performance hall
Commercial stairs

Curved and radius stair systems

Solid treads, landing platforms, curved stringers, and rail for commercial stairs. On-site precision templating in the Houston area.

A freshly milled bare oak cornice held against an existing painted cornice of the same profile at a ceiling corner
Renovation

Match-to-existing programs

Historic hotels, private clubs, and campus buildings where the new work has to disappear into the old. Knife ground from a cut-off.

Working with a general contractor?

Send the bid package or the millwork schedule. We price the lineal footage and the fabricated components as one scope, with lead times that fit the buyout calendar, and coordinate with the millwork subcontractor of record on shop drawings and delivery sequencing.

Who we supply

Shops that fabricate the rooms people remember.

A boardroom panelled in book-matched walnut framed with solid panel mould under a moulded cornice

Architectural woodwork firms

AWI-grade shops fabricating lobbies, boardrooms, libraries, and paneled rooms. We run the lineal profile so your floor stays on the casework.

A hotel guestroom corridor with moulded door casing capped by an entablature, a continuous chair rail along both walls and a cornice at the ceiling

Hospitality casework fabricators

Guestroom, corridor, and public-space packages for flagged hotels. Casing, base, crown, and panel mould by the pallet, tagged per floor.

An oak estate library with moulded bookcase face frames, a deep layered cornice and coffered ceiling beams

Luxury residential joinery

Estate work where the architect drew every cornice. Custom knives, matched species, sample stick before the run.

An oak volute fitting curling over a turned newel at a starting step, with turned balusters and a moulded skirt cap

Stair and rail companies

Solid hardwood treads, landing tread, balusters, newels, handrail, and fittings, plus the stair mouldings that finish the stringer.

What goes on the PO

Mouldings, stock, and stair parts under one PO.

The mill floor at 9915 Tanner Road — moulder and saw line, dust collection, and hardwood stacked between machines
The floor at 9915 Tanner Road. Photographed at the mill, not staged.
The mill

NW Houston / Tanner Rd. Family-operated since 1988.

Unique Wood Products mills moulding, stair treads, and custom millwork at 9915 Tanner Road in NW Houston. The knife grinder, the moulder line, and the stocked racks are under one roof, which is why a matched profile starts at our own grinder rather than a distributor’s order desk. Will-call at the counter, or Houston-metro delivery scheduled on the quote.

Trade counter
9915 Tanner Rd
Houston, TX 77041
Hours
Mon – Fri · 7:30 AM – 4:30 PM
Will-call
Staged to your PO at Tanner Rd
Delivery
Houston metro, scheduled on the quote
Terms
Cash account or net terms on approval
Before you send the first PO

What shops ask us first.

The foot of a door opening in oak — wide casing with a separate backband dying into a square plinth block, the baseboard returning into it

Do you compete with the shops you supply?

No. UWP does not bid casework and does not quote against the shops we supply. We are a mill: we run the lineal profile and fabricate solid hardwood components — jambs, panels, mantels, countertops, treads and platforms — and UWP does no install work, so mounting and field work stay with your crew. Casework and cabinetry are yours to build; the moulding behind them is ours to run.

What does a custom knife add to the job?

Knives are ground in-house rather than sent out to a tooling house. A new knife is $45 per inch of profile width, $150 minimum, and it stays on file — a reorder pays setup only. Setup is $150 under 100 LF and $95 from 100 to 399 LF; 400 LF and over is quoted with setup built in. The full schedule is published at /custom-moulding.

Is there a minimum footage on a custom profile?

Custom runs are quoted by lineal footage and species, and a sample stick is approved before the balance is scheduled. Send the footage with the drawing and the quote states what the minimum is for that profile.

Can you match a profile from a piece of the existing moulding?

Yes, and it is the most reliable way to match. Bring the broken piece to the Tanner Rd yard, or attach a photo to a quote. If nothing in the catalogue lines up, that is a knife we can grind — and a sample stick goes out for approval before the run.

Pickup or delivery?

Will-call at 9915 Tanner Road in NW Houston, staged to your PO, or Houston-metro delivery scheduled on the quote — priced on the same sheet as the material so nothing lands on the invoice after the fact.

Do you supply CAD for the profiles?

Every stocked profile carrying a traced milled section downloads as a DXF and as an ANSI-A dimensioned shop drawing, straight off the profile page or the section plates on this page.

All answers →

Terms used on this page

Start with one profile

Send us the profile you are running next week.

Attach the drawing and the lineal footage. You get a quote, a lead time, and — inside the Houston metro — a delivery price on the same sheet. Open a cash account for trade pricing, or apply for net terms.