Skip to main content
Unique Wood Products

Custom Thick Face-Grain Tread

Face-grain thick treads for floating and open-riser stairs, 1-3/4" to 3-1/2" thick — boards glued for the depth and laminated for the thickness, milled at NW Houston / Tanner Rd. Square or eased edge, supplied unfinished.

  • Custom quote
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Loading configurator…
UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
What this configurator builds

Wide-plank thick treads for floating stairs, laminated in Houston.

This configurator specifies a solid face-grain thick tread — hardwood boards glued edge-to-edge for the depth, then laminated in horizontal layers for the thickness — cut to your exact length, depth and thickness for an open-riser or floating stair. The full plank grain shows on the walking surface and the layers show on the cut end, with no obvious “good side.” There is no nosing: the slab is the whole step, with a square or 1/8" eased edge, supplied unfinished. Fabricated in-house at the NW Houston / Tanner Rd mill and priced by hand.

Sold to the trade, drawn for the submittal.

We supply building-material suppliers, wholesale distributors and commercial contractors. The configuration hands back an ANSI A shop drawing with the laminations shown in section and a DXF for the architect's set, both under the same reference as the spec sheet. Want the harder, tighter butcher-block surface? The edge-grain-up thick tread turns the staves on edge. For a standard stair, the stocked and custom 1" line is in the stair tread catalog.

Where a thick tread goes

The tread is the step
on an open-riser stair.

Floating and open-riser stairs have no riser board and no nosing — each thick slab sits on a steel stringer or wall bracket and carries the load on its own. Face-grain construction glues boards for the depth and laminates them for the thickness, for a plank look on the walking surface.

  1. Length, along the front edge

    Bracket to bracket plus the overhang you want each side, or wall to the open end on a wall-hung stair. 36"–72" in the configurator; longer by quote.

  2. Depth, the whole step

    Front edge to back edge. There is no separate nose to add — what you measure is the finished tread. 10"–24".

  3. Thickness, for the look and the span

    1-3/4" to 3-1/2". Thicker for longer spans and a heavier profile. Every thick tread is quoted by hand.

Where a thick tread goes and how to measure oneSection through three thick 2 inch treads on an open-riser stair carried by a steel mono stringer with a bracket under each tread; no risers and no nose overhang. A second drawing shows one tread in plan with length and depth dimensioned, and an end view with the thickness range.SECTION · THICK TREAD ON AN OPEN-RISER STAIRNo riser, no nose overhang — the 2" face-grain slab is the whole step.steel stringer11" deepthe whole step, no nose to add2"thick7-1/2"risebracketDrawn to scale · 7-1/2" rise · 10" run · 11" × 2" treads on a mono stringerHOW TO MEASURE · THREE NUMBERSLength, depth and thickness — square or 1/8" eased edges all round.48" · length36"–72" configured · longer by quote11"deep, front to backfront edge · square or 1/8" eased, your choice2"1-3/4"–3-1/2"end viewboards glued for depth, laminated for thicknessLength: bracket to bracket plus the overhang you want, or wall to the open end.Depth: the full step front to back — there is no separate nose to add.
Top: section through an open-riser stair — thick slabs on a steel mono stringer, a bracket under each, no riser and no nose. Below: one tread in plan with length and depth, and the end view with the thickness range.
Which tread

Three treads, one mill — side by side.

The 1" tread is priced on its page; both thick treads are quoted by hand. Everything else that separates them is here.

Custom 1" treadButcher block (EGU)Face-grain thick tread · this page
Thickness1" solid2" to 4"1-3/4" to 3-1/2"
ConstructionEdge-glued solid boards, face upNarrow staves on edge, glued butcher-block styleBoards edge-glued for depth, laminated in horizontal layers
Walking surfacePlank grainTight, linear edge grainPlank grain
Cut end showsBoard end grainEach stave’s end grain, side by sideThe laminated layers
Front edgeFull bullnose (8070) or 1/8" eased (8072)Square or 1/8" easedSquare or 1/8" eased
Returns & nosingMitred returns either end; nosing on any edgeNone — the slab is the whole stepNone — the slab is the whole step
Where it goesClosed-stringer stairs over a riser; retro-fitOpen-riser and floating stairs on brackets or a mono stringerOpen-riser and floating stairs on brackets or a mono stringer
Stability in Houston humidityGoodBest — alternating staves cancel movementGood — layers stiffen the slab
Size range24–96" long · 6–32" deep36–72" long · 10–24" deep36–72" long · 10–24" deep
PricePlanning estimate on the pageQuoted by hand — the most labour of the threeQuoted by hand
DocumentsEstimate · shop drawing · DXFSpec sheet · shop drawing · DXFSpec sheet · shop drawing · DXF
Why face grain

The plank way to build a thick tread.

In a face-grain tread, wide solid boards are glued edge-to-edge with their faces up, so the cathedral figure of the plank runs the length of the step. Because hardwood is milled 4/4 to 12/4, the thickness is built by laminating layers face-to-face — the layers show as horizontal lines on the cut end, and the top reads as one wide board.

  • Continuous plank grain. The warmest, most furniture-like surface of the two constructions.
  • Laminated for thickness. 1¾" to 3½" built from standard lumber thicknesses; finished size always as ordered.
  • Rift & quartered on request. Straight, quiet grain in White Oak or Maple for contemporary stairs.
  • Square or 1/8" eased edge. The two edges we mill on a slab — pick either in the configurator. Supplied unfinished.
Diagram comparing a face-grain side view with an edge-grain-up (EGU) side view of a 3 inch thick tread
Face grain vs. edge grain up — the same 3" tread, two constructions.
The species we mill

A few of the builds we mill.

Red Oak, White Oak, Walnut and Maple, flat-sawn and rift & quartered. Hickory and custom species are milled the same way; name yours in the configurator.

Red Oak thick face-grain stair tread
Red Oak
White Oak thick face-grain stair tread
White Oak
White Oak rift & quartered thick face-grain stair tread
White Oak · Rift & Quartered
Walnut thick face-grain stair tread
Walnut
Maple thick face-grain stair tread
Maple
Maple rift & quartered thick face-grain stair tread
Maple · Rift & Quartered

Looking for stocked 1" treads instead? Browse the stair tread catalog.

What moves the quote

No price on the page — here is what sets it.

Six things decide the number the office sends back. None of them is a secret, so they are listed. The relative cost tiers come from the same species catalogue as /wood-species.

Species

Relative material cost, red oak as the baseline: Red Oak · everyday, White Oak · premium, Maple · mid, Walnut · feature, Hickory · mid. Rift & quartered cuts and named species outside the tiles are quoted on the lumber available that week.

Board feet

Length × depth × thickness. Thickness is the lever most people underestimate: a 4" tread is twice the wood of a 2" one, and thick stock is scarcer per board foot than 4/4.

Construction labour

Ripping, jointing and gluing staves on edge is more bench time than laminating boards; both are more than a 1" tread. The shop prices the hours, not just the wood.

Quantity

A stair of twelve matched treads and one replacement tread are different jobs: setup, grain selection and glue-up are spread across the run. Put the whole count on the quote list.

Oversize and seams

Past 72" long or 24" deep the tread is a special glue-up from longer stock and is quoted on request.

Why no price on the page

The 1" tread has a stable schedule behind it. A thick glue-up depends on which boards are on the rack that week, so a number on the page would be either padded or wrong. The office quotes what it will actually build.

Species on the tilesRelative material costApprox. densityAvailability
Red OakEveryday44 lb/ft³Made to order · confirmed at quote
White OakPremium47 lb/ft³Made to order · confirmed at quote
MapleMid44 lb/ft³Made to order · confirmed at quote
WalnutFeature38 lb/ft³Made to order · confirmed at quote
HickoryMid51 lb/ft³Made to order · confirmed at quote

Cost tiers are relative positions, not prices. Densities are published air-dry averages (USDA Wood Handbook) and drive the approximate weight the configurator shows — plan brackets and handling from that figure, not from the species name.

Specifications

The full spec sheet. For the builder who scrolled this far.

ConstructionFace grain — solid hardwood, never veneered
Thickness1-3/4–3-1/2"
DimensionsDepth 10–24" · length 36–72"· larger by quote
EdgesSquare or 1/8" eased, all arrises — no other profiles
SurfaceUnfinished, sanded 120 grit — site finish by others
MoistureKiln-dried 6–9% MC · acclimate 72 hrs on site
TolerancesLength & depth ±1/16" · thickness ±1/32"
SpeciesRed Oak, White Oak, Maple, Walnut, Hickory — or name yours
FabricatedIn-house at NW Houston / Tanner Rd · will-call pickup
Lead timeConfirmed at quote
Minimum order1 piece
DocumentsSpec sheet · ANSI A shop drawing · DXF
Included · by others

What the quote covers, and what it doesn't.

Included
  • ✓Milling to the configured size, square or eased
  • ✓Kiln-dried solid hardwood, glued and sanded 120 grit
  • ✓Spec sheet, ANSI A shop drawing and DXF for the submittal
  • ✓One-year material-and-workmanship coverage under the UWP stair parts warranty
  • ✓Will-call at NW Houston / Tanner Rd
By others · not included
  • —Finish — oil, stain, lacquer or hardwax, on site after fitting
  • —Installation, brackets, pins and the stringer they fasten to
  • —Structural design of a floating or open-riser stair and its code compliance
  • —Field measure — send finished dimensions; UWP cuts to the number you give

Coverage per the UWP stair parts warranty. Movement, checking and colour change from site conditions or finishing are not defects.

How the quote works

Five steps, no surprises.

  1. Configure and add to the quote list

    The line carries every choice you made, the same reference the documents print, and no price.

  2. Submit with your contact details

    One form for the whole list. Attach a drawing if the stair or the kitchen has one; a photo of the space helps.

  3. UWP reviews the spec

    Species against the rack, construction against the size, anything that will not glue up as drawn. Questions come back to you before a number does.

  4. Written quote with lead time

    Price per piece, the lead time the shop can actually hold that week, and the seam or stock notes that apply. Valid as stated on the quote.

  5. Deposit releases the job

    Custom and special orders take a 50% non-refundable deposit and are non-returnable; the balance is due at pickup. Changes after release are re-quoted.

Terms as published in the store policies: payment on receipt unless a credit account is established, shortage or damage claims within 3 business days, Texas sales-tax exemption by certificate before invoicing.

Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the stair disappears into the room instead of fighting it.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Made to order
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Made to order
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Popular wood species

The species we run most.

Every species here is custom-milled to order — Janka hardness is listed for reference. All are solid hardwood, glued up, and refinishable for decades.

Red Oak
Made to order
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Made to order
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

Are these solid wood or veneered?
Solid hardwood throughout — never veneered. A face-grain tread is built from solid boards glued edge-to-edge for the depth and laminated in horizontal layers for the thickness. What you sand into is more of the same wood.
What thicknesses and sizes do you build?
1¾", 2", 2½", 3", and 3½" thick; 10–24" deep; and 36–72" long as standard — larger on request. Every tread is milled to your exact spec.
Why might the thickness be built from different boards?
Because hardwood is milled in standard thicknesses from 4/4 to 12/4, we may combine boards of differing thicknesses to reach your specified thickness, depending on the lumber on hand. The finished tread always meets the size you order and is glued and finish-sanded as one solid piece — the layers show on the cut end, the plank grain shows on top.
What edge do they come with?
Square, or a 1/8" ease on every arris — your choice in the configurator, same quote either way. Those are the two edges UWP mills on a thick tread; there is no bullnose on a slab because the tread has no separate nosing.
What is the difference between face grain and edge grain (butcher block)?
Face grain glues wider solid boards face-up for a continuous, warm wide-plank look. Edge grain up (butcher block) turns narrow staves on edge for a harder, tighter, more uniform top. We build both — see our EGU thick treads for the butcher-block version.
Which species can I get?
Red Oak, White Oak, Maple, Walnut and Hickory are on the tiles; Ash, Poplar (paint grade), and rift & quartered White Oak or Maple are run to order. Name any species in the configurator and we’ll confirm availability.
Do you show pricing here?
No — thick treads are quoted by hand because species, size, and quantity all move the number. Build your exact spec in the configurator, add it to your quote list, and UWP reviews it before issuing a written quote. The shop drawing and DXF carry no price either.
Do they come finished?
No. Every thick tread is supplied unfinished, sanded to 120 grit, for your finisher to seal on site. Acclimate it 72 hours before finishing.
How are floating treads mounted?
With hidden brackets, steel pins, or anchors fastened to reinforced wall framing or a concealed stringer — handled by your builder or stair installer. We supply the hardwood tread, milled to spec; UWP does no install work.
Pickup or delivery?
Current material availability, production timing, pickup, and delivery are confirmed on the written quote after UWP reviews the exact SKU, species, quantity, geometry, and shop capacity.
All answers →

Terms used on this page