Skip to main content
Unique Wood Products

How do I install hardwood stair treads?

A confident DIYer can install a hardwood stair tread retrofit in a weekend. The sequence: pull carpet and staples, prep the substrate flat and quiet, acclimate the treads for 5 to 7 days, dry-fit each tread, glue with a urethane construction adhesive, fasten with stainless trim screws (countersunk), plug, sand, and finish. Risers go in before treads on a full build; after, on a retrofit.

The short version

  • Acclimate first. Stack the treads in the install space for 5 to 7 days before fitting. Skip this and the treads will move after install regardless of how well you installed them.
  • Strip and prep. Pull carpet, padding, and every staple. Screw down squeaks in the substrate. Confirm the substrate is flat — scribe or shim as needed.
  • Glue + fasten. Bed each tread in a continuous urethane construction adhesive bead, fasten with stainless trim screws (countersunk and plugged), or use mitered finish nails on solid wood treads where holes will be hidden.
  • Finish on-site. Site-finishing gives you the cleanest color match and the chance to address any scratches from install. Plan for a 24-hour cure before walking the stairs.

The full answer

A confident DIYer can install a hardwood stair tread retrofit in a weekend. A new-build install is a different scope — bigger project, framing involved — but the finish-carpentry side of installing the treads uses the same techniques. Below is the honest walkthrough. For the full step-by-step with diagrams, **download the UWP Stair Tread & Riser Installation Guide** — this answer is the overview.

Tools you’ll need

  • Pry bar, hammer, pliers (for carpet, padding, and every single staple that’s left behind)
  • Drill / driver with a countersink bit
  • Miter saw or circular saw with a sharp finish blade
  • Construction adhesive (urethane, e.g. Loctite PL Premium or equivalent)
  • Stainless steel trim screws sized for your tread thickness
  • Wood plugs to match species (or accept a filled hole)
  • Sandpaper from 80 to 220 grit
  • Wood filler (color-matched, if not plugging)
  • Tape measure, level, scribe, framing square
  • Knee pads (you will use them)

Step 1 — Acclimate the treads (5 to 7 days)

Stack the treads in the install space — not the garage, not the front porch — for 5 to 7 days before installation. The wood needs to reach the room’s equilibrium moisture content before being permanently fastened down. Skip this step and the treads will swell or shrink after install, opening gaps or cupping. Houston-conditioned interiors usually settle within a normal range; the acclimation week is non-negotiable.

Step 2 — Strip the existing stair

For a retrofit install over a carpeted stair:

  • Pull the carpet runner and pad. Roll cleanly so you can dispose without dragging staples everywhere.
  • Pull every staple. Use needle-nose pliers and a magnetic sweeper. Carpet staples left behind are the #1 source of black iron-tannate stains on white oak installs.
  • Pull any tack strip nailed into the treads.
  • Look at the substrate — usually rough plywood or pine. Walk every step listening for squeaks; screw down the squeaks with deck screws into the stringer.

Step 3 — Confirm the skirt-board math

If your stair has wooden skirt boards (the trim running along the wall beside the stairs), check the height. On most carpeted stairs, the skirt sits about 11/16″ proud of the bare substrate. An 8071 retro-fit tread (5/8″ body) lands flush with the skirt; an 8070 full tread (1″ body) sits about 1/4″ proud. If you ordered the wrong product for your stair, stop now — see the 8070-vs-8071 question.

Step 4 — Install risers first (or last)

On a new build or full demo, risers usually go in first — the tread then traps the top edge of the riser, no exposed seam.

On a retrofit, risers can go in either before or after, depending on whether you’re also overlaying the risers. If you’re only doing treads, skip riser installation entirely — the existing risers paint over.

Step 5 — Dry-fit each tread

Lay every tread on its step without adhesive first. Check the fit against the skirt board on each side. Most stair openings are not perfectly square — you’ll find a tread is 1/16″ too wide on one side, or the back edge needs a slight scribe to follow an uneven riser. Mark each tread with its step number on the underside before you trim — every step is slightly different and you don’t want to re-cut by accident.

Step 6 — Glue and fasten

Lay a continuous serpentine bead of urethane construction adhesive across the substrate — front to back, side to side, no gaps. The adhesive does the real holding work; fasteners just keep the tread from moving while the adhesive cures.

Fastener choice:

  • Stainless trim screws, countersunk and plugged. This is the cleanest method on retrofit treads where the screw head would otherwise show. Match the plug species to the tread species.
  • Stainless finish nails through the front edge of the tread into the riser top. Set the heads slightly proud, fill with color-matched wood filler before final sanding.
  • Trim-head screws toe-nailed through the back of the tread into the riser below. Hidden.
  • Never use standard steel screws or staples on white oak — see the iron-tannate question. Stainless or epoxy-coated only.

Step 7 — Set, sand, finish

Once every tread is glued and fastened, give the adhesive its full cure time (usually 24 hours; check the tube). Don’t walk the stairs during cure — set up a path through another route if possible.

When cure is complete: light sand the entire stair with 120 grit, then 180, then 220. Vacuum and tack-cloth. Apply stain (if any), then 2–3 coats of polyurethane (or your finish of choice), sanding lightly between coats with 320 grit.

When to call a pro

A straight-run retrofit stair is DIY-friendly. The following are not:

  • Curved stairs. Each tread is a unique shape that must be templated. See curved stair treads.
  • Stairs out of square. If your stair has accumulated 1″+ of out-of-square over its run, scribing every tread is finish-carpentry territory.
  • Open-rise / floating stairs. These are full-build projects, not retrofits.
  • Thick treads (1¾″+). See the thick tread retrofit question — these aren’t retrofit material.

For everything in scope, the full installation guide PDF has diagrams, dimension callouts, and the specific glue-and-fastener detail. Download it before you start.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-27