Skip to main content
Unique Wood Products
Wide plank white oak flooring in warm afternoon light, grain and color variation in focus
Milled in NW Houston · Long Lengths

Hardwood Flooring, Milled in Houston.

Solid Wide Plank · Engineered · Unfinished

Solid White Oak and Red Oak, wide plank, in long lengths to 12 feet — milled to order at our Tanner Road shop. Plus stocked engineered European White Oak for slab-on-grade. We supply the floor; your installer finishes it on site.

We supply the material

UWP mills and stocks the flooring — solid wide-plank oak milled to order, plus stocked engineered European White Oak. Supplied from the NW Houston yard for will-call.

Your installer finishes it

Layout, install, sanding, and finishing are handled by your flooring contractor or NWFA-certified installer — we don't install, so there's no conflict with your finishing trades.

A room mid-install: half the floor laid in wide plank unfinished white oak, the rest still plywood subfloor, a mallet and tapping block on the boards
Two ways to floor in oak

Pick the floor that fits your subfloor.

Our specialty

Solid Milled Wide Plank

The look commodity strip lines can't run — solid oak, wide and long, milled to order.

  • · Solid 3/4" White Oak, Red Oak & more
  • · 6"–11" wide plank · long lengths to 12 ft
  • · Tongue & groove · micro-bevel or square edge · unfinished
  • · Installs over a wood subfloor
Configure & Quote →
Core program · confirm at quote

Engineered European White Oak

Dimensionally stable for slab-on-grade and radiant — where solid is harder to install.

  • · Engineered 5/8" plank · 4mm wear layer
  • · 7-1/2" and 9-1/2" wide
  • · Beveled edge · random lengths · unfinished
  • · Stable over concrete & radiant heat
See Specs →
SubfloorSolid 3/4" wide plankEngineered 5/8" EWO
Plywood or OSB over joists (pier & beam, second floor)Yes — nail-down or staple-down, the floor it was made for.Yes — nail, glue or float.
Concrete slab on gradeOnly over a plywood subfloor or sleepers on a moisture barrier; not direct to the slab.Yes — glue-down or float over a moisture barrier. The reason it is stocked.
Radiant heatNot recommended; wide solid boards move too much over a heated slab.Yes, within the heating system’s surface-temperature limit.
Below grade (basement)No.Yes, with moisture testing and a vapour barrier.

General guidance for a conditioned Houston house. Your installer confirms the method against the actual slab or deck, its moisture reading and the manufacturer's instructions for the engineered plank.

Milled to order

Solid wide-plank oak.

We don't chase commodity strip flooring — we can't beat the high-volume mills on price, and we don't pretend to. What we do instead is mill what those lines can't: solid hardwood, wide plank, in long lengths — White Oak, Red Oak, Maple, Hickory, Rift & Quartered, European Oak, Reclaimed, and Heart of Pine, cut and surfaced in-house at our NW Houston / Tanner Road shop.

Long boards mean fewer end joints and a calmer, genuinely high-end floor. Tongue-and-groove on the long edges so it lays tight; ends are square-cut (we don't end-match) and trimmed to the framing on install. Left unfinished for your installer to sand and finish on site.

White Oak plank under a clear matte finish
White OakThe wide-plank standardWarm tan with an olive cast, straight grain in rift and quartered cuts. The species most wide-plank floors are specified in.
Red Oak plank under a clear matte finish
Red OakTraditionalWarmer and redder with a bolder cathedral grain. Takes stain evenly; the classic Houston floor.
Maple plank under a clear matte finish
MaplePale and quietFine, even grain and a creamy colour that reads modern under a clear coat. Harder than either oak.
Hickory plank under a clear matte finish
HickoryHigh characterStrong colour variation from cream to brown and the hardest of the four. Rustic or contemporary depending on the grade.

Also milled: Rift & quartered White Oak · European Oak · Reclaimed · Heart of Pine · or your spec. Plank studies simulate a water-clear matte coat; material ships unfinished and colour varies by board. Want a species not shown? Type it into the configurator.

Solid floor — mill spec
Species
White Oak · Red Oak · Maple · Hickory · R&Q · Euro · Reclaimed · Heart of Pine — or your spec
Construction
Solid sawn — one piece, top to bottom
Face Width
6"–11" · 11"+ custom (any width milled to your spec)
Thickness
3/4" solid (the one we run)
Lengths
Long run — to 12 ft
Profile
Tongue & groove long edges · butt ends (not end-matched)
Edge
Micro-bevel or square — your choice at quote
Grades
Select & Better · Character (#1 Common) · or your grade
Surface
Unfinished — sand & finish on site
Order type
Every order custom-milled to spec — quoted by hand
Milled
In-house · NW Houston / Tanner Rd

Every floor is custom-milled to your spec — species, width, grade, and length. Square-edge / face-nail and prefinishing available on request.

CONFIGURE YOUR WIDE-PLANK FLOOR

PRICING

Custom quote

Solid flooring is milled to order — species, width, length, grade, and square footage all move the number. Build your spec below and we'll price it.

1 · SPECIES & CUT

Pick a species or type in your own — every floor is milled to your spec.

Every floor is custom-milled: White Oak, Red Oak, Maple, Hickory, Rift & Quartered, European Oak, Reclaimed, and Heart of Pine — all cut to order at our NW Houston / Tanner Rd shop. Wide stock and long lengths are a high-end, made-to-spec run, so it's priced by the job. Want something else? Choose “Custom species” and tell us what you have in mind.

2 · PLANK SIZE

Wide plank 6–11" face width · long lengths to 12′. Need wider? Choose Custom and type in any width — it's all milled to spec.

Not sure on footage? Use our square-footage calculator or send us your room dimensions in the notes.

3 · MILL SPEC

Our standard solid floor build. Thickness is 3/4" — the one we run.

Thickness:
3/4" solid
Profile:
Tongue & groove long edges · butt ends (not end-matched)
Finish:
Unfinished — sand & finish on site

Micro-bevel — a slight V-groove along each board edge; forgiving on a wide-plank floor. Square — edges meet flush for a seamless, monolithic look.

4 · YOUR CONFIGURATION

Product:
Solid Milled Wide-Plank Floor
Species:
White Oak
Plank:
7" wide · Extra-long — to 12′
Grade:
Select & Better
Thickness:
3/4" solid
Edge:
Micro-bevel
Area:
To be confirmed
Lead time:
Quoted with your order

5 · REQUEST A QUOTE

UWP will review and price this exact spec before following up.

Your spec: Solid Wide-Plank Floor · White Oak · 7" wide · Extra-long — to 12′ · Select & Better · 3/4" solid · Tongue & groove long edges · butt ends (not end-matched) · Micro-bevel edge · Unfinished — sand & finish on site
Or call (713) 462-5045

By submitting, you agree we may contact you about this request. We don't share your information.

From our shop floor

Milled here, not imported.

Solid oak, run wide and long and bundled at our NW Houston / Tanner Road shop — tongue-and-groove on the long edges, square-cut ends. This is the actual product, not a catalog render.

Stacks of wide-plank solid oak flooring milled and ready at UWP
Wide plank, milled to order — stacked and ready for pickup.
Long-length solid oak flooring boards bundled at UWP's Tanner Road shop
Long lengths — the run commodity strip lines can't yield.

Bundled by width

Boards are bundled and strapped by face width, long lengths to 12 ft. Random lengths across the run unless the quote specifies otherwise.

Tongue & groove, square ends

The long edges are milled tongue and groove so the boards lock side to side. Ends are square-cut, not end-matched, and fall on the framing when your installer trims them.

Kiln-dried, unfinished

Kiln-dried hardwood, sanded on the face, no finish. Acclimate it in the conditioned house before the first board goes down; the moisture reading is on the quote.

Grade as ordered

Select & Better runs clean and even in colour; Character (#1 Common) carries the knots and streaks. Rift & quartered cuts are sorted for straight grain.

A long hallway floored in wide plank white oak, the boards running away from the camera in long unbroken lengths with very few end joints
Long lengths

Boards to 12 feet: fewer end joints, a calmer floor.

Finished on site

Unfinished is the point.

A prefinished floor arrives with somebody else's colour, sheen and a bevel at every board. Ours arrives sanded and bare. Your installer lays it, sands it flat as one surface, then stains and seals it in the room — so the colour is chosen against the light and the cabinets that are actually there, and the floor reads as one piece rather than a hundred boards with a bevel between them.

  • Stain, natural, whitewashed or fumed — decided on a sample board on site.
  • Oil, hardwax or water-based polyurethane; matte to satin, the installer's call.
  • Square edge sands flush and seamless; micro-bevel keeps a fine line at each board.
  • 3/4" solid re-sands for decades; the 4mm wear layer on the engineered plank does the same.
A freshly sanded wide plank white oak floor, the near half coated with a clear sealer and reading a shade warmer than the bare boards beyond
The wet line: bare white oak on the far side, sealed on the near.
A traditional living room with a wide plank red oak floor, warm reddish tan with bold cathedral grain under a satin finish
Red oak, wide plank, site-finished satin: the traditional Houston floor.
Stocked unfinished

Engineered European White Oak.

For slab-on-grade and radiant — where a solid floor is harder to install — a 5/8" engineered plank with a 4mm hardwood wear layer over a balanced cross-ply core. Stable for Houston humidity, and thick enough to refinish for decades.

A stack of unfinished engineered European white oak planks on a concrete slab, one turned on end to show the cross-ply core under the hardwood wear layer
The section: a 4mm oak face over a cross-ply core, which is what holds the board flat over a slab.
Specification7-1/2" Plank9-1/2" Plank
MaterialEngineered European White OakEngineered European White Oak
Width7-1/2"9-1/2"
Total Thickness5/8"5/8"
Wear Layer4mm Hardwood4mm Hardwood
LengthsRandom, up to 75"Random, up to 86"
Edge ProfileBeveledBeveled
ConstructionBalanced / Cross-Ply CoreBalanced / Cross-Ply Core
SurfaceUnfinished — sand & finish on siteUnfinished — sand & finish on site
Coverage / Carton23.44 sq. ft.34.10 sq. ft.
Trade supply

Send your takeoff — we'll mill the floor.

Build your solid wide-plank spec in the configurator, or tell us the species, width, and square footage and we'll quote it. Your installer handles the finish on site.

NW Houston · Tanner Rd Yard · Will-call & metro delivery

Free buyer's guide

A guide your customers can hold in their hands.

Selling solid wide plank to a homeowner? Hand them our buyer's guide. Nine pages on why solid wood, the wide-plank difference, the cuts, the species, width and grade, and finishing — the whole decision, laid out plainly, so the floor specs cleanly the first time.

  • · Plain · rift · quartered — with cut diagrams
  • · Nine species, hardness, and character
  • · Width, length & grade — how to spec it
  • · Texture, stain & site-finishing

Start with the wood species guide — Janka hardness, tone, and grain for every species we run.

Wide plank white oak flooring detail — UWP buyer's guide
PDF

Guide to Wide Plank Wood Floors

A homeowner's buyer's guide to solid wide-plank floors — milled wide & long in Houston, unfinished, finished on site.

Download PDF
Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

Solid milled or engineered — which do I want?
Solid wide plank is our specialty: 3/4" solid White Oak or Red Oak, milled to order at our Tanner Road shop in long lengths to 12 feet — the look commodity strip lines can’t run. It installs over a wood subfloor and refinishes for the life of the house. Engineered European White Oak is the core catalog option: a dimensionally stable 5/8" plank built for slab-on-grade and radiant, where a solid floor is harder to install. Tell us your subfloor and we’ll point you to the right one.
Why long lengths, and why does it matter?
Commodity strip flooring ships in short random lengths because that’s what high-volume mills can yield cheaply. Because we mill in-house, we run solid oak in long lengths to 12 feet — fewer end joints, a calmer floor, and a genuinely high-end result. We don’t compete on price with commodity strip; we mill what those lines can’t.
Do you install flooring?
No — we supply the material. UWP mills and stocks the flooring; your flooring contractor or NWFA-certified installer handles layout, install, sanding, and finishing on site. We are happy to coordinate with your installer on quantities and lead times.
Nail-down, glue-down or floating?
Solid 3/4" plank is nailed or stapled down through the tongue into a wood subfloor; that is the only method we recommend for it. The engineered plank can be nailed over wood, glued to a slab, or floated over an underlayment. The subfloor table above matches the method to the floor; your installer confirms it for the house.
Can solid wide plank go over a concrete slab?
Not directly. Over a slab, solid boards need a plywood subfloor or sleepers on a moisture barrier first, which adds height and cost — so on slab-on-grade, which is most of Houston, we point people to the engineered European White Oak. If the house is pier and beam, solid is the floor.
Why unfinished?
Unfinished flooring gives the trade complete control over color, sheen, and character — sanded, stained, and finished on site for a truly bespoke result, with the boards flush and seamless. Solid 3/4" oak sands and refinishes for decades; the engineered plank’s 4mm hardwood wear layer does the same.
What species and grades do you mill?
Solid flooring runs in White Oak, Red Oak, Maple, Hickory, Rift & Quartered White Oak, European Oak, Reclaimed, and Heart of Pine — in Select & Better or Character (#1 Common) grade. Anything else is milled to order, subject to lumber availability; pick “Custom species” in the configurator and tell us what you want.
How wide can you go?
We mill solid flooring 6" to 11" wide, and 11"-and-wider as a custom run. Be aware that genuinely wide White Oak lumber is hard to source — the boards simply aren’t common — so the widest White Oak runs depend on what’s available when we mill. Tell us the width you want (choose “Custom” for 11"+) and we’ll confirm it on the quote.
Is the flooring tongue-and-groove? Is it end-matched?
We mill tongue-and-groove on the long edges, so the boards lock side to side and lay tight. The ends are square-cut — we do not end-match. Your installer trims the board ends to fall on the framing, which is standard practice for site-finished solid flooring. Long lengths mean fewer end joints to deal with in the first place.
How much do I need?
Use our floor square-footage calculator to estimate, and the mixed-width calculator if you are blending plank widths. Add the trade-standard waste factor for your install method, or send us your room dimensions and we will work it out.
Do you show pricing here?
No — every floor is custom-milled to spec, so it’s priced by species, width, length, grade, and footage. Wide stock and long lengths are a high-end, made-to-order run. Build your spec in the configurator and we’ll quote it, or call the Tanner Road yard.
Pickup or delivery?
Current material availability, production timing, pickup, and delivery are confirmed on the written quote after UWP reviews the exact SKU, species, quantity, geometry, and shop capacity.

Part of our hardwood millwork program. Need dimension stock instead? See our S4S & S3S lumber, or the engineered flooring warranty for coverage details.

All answers →