1 · Foreword · Scope & system
Read this first
Post-to-post — the workhorse system.
This guide covers the post-to-post wood handrail and newel system that UWP supplies through the NW Houston / Tanner Rd yard (special order) — square-top newels with the handrail butted into the post face and joined with a rail bolt. It is the IRC-friendliest system for residential stairs and the one most trim carpenters reach for first. Over-the-post (pin-top newel with continuous fittings) is a separate appendix and not covered here.
2 · Components · System anatomy
Know the pieces before you cut
What goes where.
Figure in the PDF: Post-to-post stair — side elevation showing the four primary components
Starting newel — the bottom-of-stair newel; carries the lower end of the handrail and one side of the guard.
Landing / intermediate newel — used where the rail pitches change or at a landing turn. Same anchor logic as a top newel.
Top newel — at the upper end of the rake, butted to the second-floor framing. Carries the top of the rail.
Pitch / rake — the angle of the stair, set by rise-over-run. Captured with a pitch block (see page 9).
Plow — a square channel routed in the underside of the handrail to receive square wood balusters and fillet pieces.
Fillet — thin wood strips that fill the plow between balusters, set the spacing, and finish the underside.
Rosette — a small wood plate mounted on the wall to receive the end of a handrail terminating at the wall (UW-7017).
Rail bolt — the threaded stud + tee-nut hardware that pulls the handrail tight against the newel face.
3 · Inventory · Newels
The posts UWP carries
Box newels and turned newels.
UWP carries the wood newel families most commonly specified on Houston-area residential stairs, in box and turned profiles. Newels are special order — profile, species and timing are confirmed at quote. Box newels are listed in red oak and poplar; turned newels in red oak.
- UW-4091
- Box newel, 5-1/2" sq.
- 55" · oak, maple, WO
- UW-4091XL
- XL box newel, 6-1/4" sq.
- 55" · oak, maple
- UW-4091R
- Box newel, reverse panel
- 55"
- UW-4091F
- Box newel, fluted
- 55" · XL also
- UW-4075
- Box newel, 3-1/2" sq.
- 56" · oak, maple, WO
- UW-4075SL
- Sleeve for the 4075
- 22-1/4"
- UW-4000
- Chamfered box newel, 3-1/4" sq.
- 56" · oak, maple, WO
- UW-4002
- Chamfered box newel, 3-1/2" sq.
- 56"
- UW-4091PTOP
- Pyramid cap for box newels
- 5-1/2" · 6-1/4" XL
- UW-4091FTOP
- Flat cap for box newels
- 5-1/2"
- UW-4015
- 3" turned landing newel
- 58"
- UW-4040
- 3" turned starting newel
- 47-5/8"
- UW-4042
- 3" turned starting newel
- 57-5/8" · WO 54"
- UW-4045
- 3" turned landing newel
- 57-5/8" · WO also
- UW-4046
- 3" turned landing newel
- 62"
- UW-4045BT
- Sloped pin-top landing newel
- 57-5/8"
- UW-4500
- 3-1/2" turned starting newel
- 48"
- UW-4010
- 3" turned starting newel
- 43" · WO also
4 · Inventory · Handrail profiles
Two profile families do most of the work
Pick the rail, then pick the variant.
Figure in the PDF: UW-6010 · American Classic
Figure in the PDF: UW-6210 · Classic — slightly wider, lower
Figure in the PDF: UW-6010P · Plowed for square balusters
- UW-6010
- 6010 handrail, finger-joint oak
- 8–20 ft · most common
- UW-6010SC
- 6010 white oak, solid cap
- 8 / 12 ft
- UW-6010FJ1
- 6010 white oak, finger-joint
- 16 ft
- UW-6010-16-P
- 6010 poplar
- 16 ft · paint grade
- UW-6210
- 6210 handrail, oak
- 8–20 ft · wider profile
- UW-6210SC
- 6210 white oak, solid cap
- 8–12 ft
- UW-6210FJ1
- 6210 white oak, finger-joint
- 14 / 16 ft
- UW-6710
- 6710 handrail, oak
- 8–20 ft · 2-3/4" stock
- UW-6010P
- 6010 plowed (for sq. balusters)
- 8 / 12 / 16 ft
- UW-6210P
- 6210 plowed
- Oak and white oak
- UW-6042
- 6042 plowed, flat top
- 8 / 12 / 16 ft
- UW-6040
- 6040 round wall rail
- 8–20 ft
Cut from matching species to the plow width — 1-1/4" sq. for the standard 6010P plow. Comes in 8' and 12' lengths.
5 · IRC Code · Handrails · R311.7.8
Code reference — handrails
Height, grasp, and return.
Figure in the PDF: R311.7.8.1 — handrail height (34"–38" plumb above nosing)
Figure in the PDF: TYPE I · 6010 profile
Figure in the PDF: TYPE II · finger-recess
6 · IRC Code · Guards & spacing · R312
Code reference — guards & newels
The newel is the guard.
On any open stair, the newel posts are structural guard supports. They must resist the same 200-lb concentrated load and 50-lb/ft linear load required of a guard rail under R301.5 — which drives the anchor method on page 10. Get the anchor right or the guard fails inspection.
Figure in the PDF: R312.1.3 — 4" sphere rule + R312.1.2 — 36" stair guard
Figure in the PDF: R312.1.3 exception — 6" sphere at the tread triangle
7 · Tools · Fasteners
Set the bench before the cut
Tools and hardware.
- 4-ft level (the long one — gets the newel plumb in two reads)
- 6-ft chalk line (snap the handrail line off the nosings)
- Combination square + bevel gauge (to capture the rake angle)
- Pitch block — made from 2x scrap (page 9)
- Tape measure, sharp pencil, dead-blow mallet
- Compound miter saw (12" preferred — handrails are 2-3/4" wide)
- Sharp 80T finish blade — chip-free cuts on stain-grade rail
- Hand saw / Japanese pull saw — for fillet trim cuts in place
- Block plane for fine fit at the rail-to-newel butt joint
- 1/16" cold chisel for the rail-bolt access mortise
- Cordless drill + impact driver
- 5/16" auger bit (rail-bolt access hole through handrail)
- 1/4" and 3/8" twist bits (rail-bolt pilot + tee-nut hole)
- Newel-bolt drill jig — sets bolt center on the newel face
- Forstner bits (3/4", 1") — bolt-cap recesses, plug counter-bores
- Snug-Tite / Zipbolt / standard handrail-bolt kit per joint — includes the threaded stud, tee-nut, and lock-washer
- 3/8" rail bolts are standard for 6010 / 6210 family rails
- Wood plug to cover the access hole (stock plug per species)
- Bolt-through (preferred) — 3/8" carriage bolt + nut + washer through floor blocking from below
- Lag-into-blocking — 3/8" lag screws into solid blocking under the subfloor
- Newel Fastener System (NFS) — surface lag with concealed plug cap, for retrofit where you cannot access from below
- Construction adhesive (PL Premium or equivalent) — gap-filling, structural
- Wood glue (Titebond III or equivalent — slow-set for the rail-bolt joint)
- Color-matched putty stick (for nail holes in the fillet)
- 15-gauge finish nails (2") for fillet — set with a pin nailer for tighter fastening
- Sanding sponge — 220 grit for the rail-to-newel butt edge
8 · Layout · Pitch & rail line
Layout method
Pitch block first.
Before a single newel goes down, capture the actual stair geometry. The plans say 7-3/4" riser by 10" tread — the built stair may not. The pitch block lets you carry the real rake angle to the miter saw and the newel face. Get this right and every cut downstream lines up.
Figure in the PDF: STEP 1 · Cut the pitch block from 2x scrap
Figure in the PDF: STEP 2 · Snap the rail line off the nosings
- 1
Measure the real rise and run.
On the installed stair, measure one full tread run (front of one nosing to the front of the next nosing — typically 10"–11") and one full rise (top of tread to top of next tread — typically 7-1/4"–7-3/4"). Confirm at least three steps in the flight; if they vary, average. Mark these as the working rise and run.
- 2
Cut a pitch block.
On a piece of 2x scrap 10"–12" long, lay out a right triangle with the working rise as the short leg and the working run as the long leg. Cut on the bandsaw or with a circular saw. The hypotenuse is the rake angle — this block now carries it everywhere.
- 3
Snap the rail line.
On each tread nosing, mark a target rail height. The IRC range is 34"–38" plumb above the nosing — 36-1/2" centerline target gives ½" trim margin on a stain-grade rail. Pull a chalk line through all the marks to the top newel. Confirm the line is parallel to the nosing slope — if not, one of your nosing marks is off.
- 4
Set the newel positions.
Starting newel: usually centered on or just behind the bullnose of the bottom step (depends on whether you have a starting step or a starting newel rosette block — verify from the plan). Top newel: face flush with the top riser, centered on the second-floor framing. Mark both positions.
9 · Install · Newel anchor methods
Newel install
Three ways to tie it down.
Each anchor method has a place. Bolt-through is the structural gold standard and the one that survives a strong load test. Lag-into-blocking is the carpenter's default when you have a clean joist bay below. NFS is for retrofits where the ceiling below is finished and you cannot get above the floor.
Figure in the PDF: A · BOLT-THROUGH (PREFERRED)
Figure in the PDF: B · LAG-INTO-BLOCKING
Figure in the PDF: C · NEWEL FASTENER SYSTEM (NFS)
- 1
Bolt-through — preferred.
Drill a 3/8" hole through the center of the newel base and through the subfloor. Counter-bore the top of the newel for a hex head + 3/4" wood plug. Pass a 3/8" carriage bolt through; the threaded end exits below into the joist bay. Add a fender washer and nut from below; pull the newel snug, plumb in two directions, then torque to a firm-not-stripped feel. Plug the top with matching species.
- 2
Lag-into-blocking — common.
Install solid 2x6 (or doubled-up) blocking under the floor at the newel position before drywall closes the ceiling. Set the newel and drive two 3/8" x 5" lag screws at opposing angles through the base into the blocking. Pre-drill 1/4" pilots to avoid splitting the newel base. Counter-bore for the hex heads if the screw line will be visible.
- 3
Newel Fastener System (NFS) — retrofit.
When the ceiling below is finished and you cannot reach the underside, NFS hardware lags through the side of the newel base into the rim joist or stringer. Cap holes with matching-species plugs. NFS is rated for residential code load when properly installed, but the bolt-through method is stronger if it's available.
10 · Install · Top & landing newels
The two trickiest newels
Top newel and the turn.
The starting newel is the easy one — open floor below for the bolt, clear sight lines for plumb. Top and landing newels carry the same load with less working room: the top newel butts against second-floor framing, and the landing newel takes the rail-line change. Get these two right and the rest follows.
Figure in the PDF: TOP NEWEL · Face-bolted to rim joist
- 1
Position top newel.
Pre-drill the rim joist for three through-bolts at ~3" centers. Set the newel hard against the rim, plumb both directions, and drive the bolts. The newel face stays flush with the top riser.
- 2
Trim newel height.
Mark the top-of-cap height calculated above, transfer to the newel shaft, cut on the miter saw with the pitch block off-cut for a plumb cut. Dry-fit cap, sand any roughness, glue and pin-nail.
- 3
Drill the rail-bolt access mortise.
After the newel is plumb and final, drill the 3/8" rail-bolt pilot and the 1" access mortise on the underside of the handrail (page 12). Do this in place — bench drilling guarantees a mis-line.
11 · Joinery · Rail bolt
The post-to-post key joint
Rail bolt joinery.
The rail bolt is what makes post-to-post possible. A threaded stud spans the joint — one end seats in the newel face via a tee-nut, the other end pulls the handrail tight through an access mortise routed in the rail underside. Done right, the joint is invisible from above and tighter than mortise-and-tenon.
Figure in the PDF: RAIL-BOLT JOINT · newel face left, handrail right
- 1
Mark and drill the newel face.
Center the rail-bolt hole on the newel face at the working rail height (the centerline of the rail at the butt). Drill 3/8" through the newel, perpendicular to the face. Drive the tee-nut into the rear (back) of the newel with a few hammer taps — the prongs anchor it.
- 2
Thread the stud, dry-fit the rail.
Thread the rail-bolt stud into the tee-nut from the rear, leaving ~1-1/2" projecting from the newel face. Cut the handrail to the exact length with a plumb cut on the miter saw using the pitch block as a guide. Hold the rail to the stud, mark the stud-center on the rail end.
- 3
Drill rail pilot and access mortise.
On the rail end, drill a 3/8" hole to receive the stud, ~2-1/2" deep into the rail core. On the rail underside, ~2" back from the rail end, drill a 1" Forstner access mortise to expose the stud end for nut tightening.
- 4
Glue and torque.
Apply slow-set wood glue to the rail butt and newel face. Slide the rail onto the stud, work the nut and washer through the access mortise onto the stud end. Torque the nut snug — the joint pulls the rail tight against the newel face. Clean glue squeeze-out before it sets.
- 5
Plug the access mortise.
Cut a wood plug of matching species 1" diameter, 1/4" thick. Glue and tap into the access mortise. Pare flush with a chisel and sand to 220. On a stain-grade run, grain-match the plug.
12 · Joinery · Cuts & transitions
Pitch is everything
Plumb cuts and transitions.
A rake handrail meets the newel face on a vertical plane — not the rail axis. Cut the rail end plumb (using the pitch block on the miter saw fence) and the joint closes tight without a step. The same logic governs pitch transitions: keep cuts plumb, let the newel make the angle change.
Figure in the PDF: PLUMB CUT · rake handrail meets newel face
Figure in the PDF: PITCH TRANSITION · rake to level at a landing
- 1
Set the miter saw to plumb.
With the pitch block on the saw fence (long leg flat against the fence, hypotenuse facing the blade), the rail end now cuts at exactly the rake angle. Hold the rail tight to the fence — the cut is plumb when the rail is installed on the rake.
- 2
Test fit, no glue.
Set the cut rail end against the newel face. The whole end should touch — no gap top, no gap bottom. If the top is open, the cut angle is too shallow. If the bottom is open, too steep. Adjust the pitch block, recut, retest.
- 3
Pitch transitions at landings.
Post-to-post does not run continuously through a landing change — each rail section terminates at the landing newel and a new section begins. No fittings needed. The landing newel makes the angle change visually and structurally.
- 4
Fillet install (plowed rail only).
For plowed handrails (square balusters), the fillet sits in the plow between balusters. Cut to fit between baluster tops; pin-nail with 15-ga finish nails set just below the rail underside. The fillet should be flush with the rail bottom — pre-finish if possible.
13 · Terminations · Returns & wall rails
Closing the run
Returns, rosettes and wall rails.
IRC R311.7.8.4 requires handrails to "return or terminate in newel posts or safety terminals." On a wall-side handrail or a section that doesn't end at a newel, the rail returns into the wall via a rosette. The opposite side terminates in a starting / top newel — the newel itself is the safety terminal.
Figure in the PDF: WALL RETURN · rail + UW-7017 rosette
Figure in the PDF: WALL-MOUNTED HANDRAIL · bracket spacing
- 1
Wall-side handrail termination.
Install the wall rosette (UW-7017) at the rail end. Center the rail height on the rosette — typical install is 36-1/2" centerline. Pre-drill the wall behind the rosette for the lag screw into framing; do not rely on drywall anchors. Fasten the rail end to the rosette face with two finish screws from the back side, or with rail bolts as on a newel joint.
- 2
Wall-mounted handrail brackets.
Brackets must be spaced no more than 48" on center. Each bracket must lag into framing — drywall anchors fail under the 200-lb load. Maintain 1-1/2" minimum clearance between the wall and the underside of the rail (R311.7.8.4). Round brackets must allow continuous hand travel.
- 3
Combination: newel + wall.
On a stair that runs from open guard at the bottom to a wall at the top, post-to-post handles both ends. Starting newel below; wall rosette + return at the top. Or the reverse. Either way, both ends are terminated per code.
14 · Finishing · Field & touch-up
Last 10% is the visible 90%
Finishing & touch-up.
A clean install with a sloppy finish reads as a sloppy install. The good news: the joinery is the hard part; the finish is recovery. Two paths — pre-finish off-site for a controlled coat, or field-finish for a perfect color match to surrounding trim. Both work; pick based on the species and the rest of the millwork program.
- 1
Set and fill nail holes.
Set 15-ga finish nails just below the surface with a nail set. Fill with color-matched putty stick (for stain grade) or paintable spackle (for paint grade). Match the putty to the species — red oak putty pulls red, white oak pulls amber. Wipe excess with a clean rag immediately.
- 2
Pare and sand access plugs.
Plug the rail-bolt access mortises with grain-matched plugs (page 12). Pare flush with a sharp chisel — leave a tiny crown, then sand flush with 220 grit. Done right, you cannot find the plug under a stain.
- 3
Sand the butt joints.
At each rail-to-newel butt, the joint is line-tight from the rail-bolt tension but the wood surface may have a 0.005" misalignment. Block-sand the joint with 180 then 220 — light strokes parallel to the rail axis, both pieces at once. The joint becomes invisible to the hand.
- 4
Stain and topcoat.
Stain in even strokes along the grain, wipe back to set the color. Test on a scrap end-cut before committing — handrail wood and floor wood take stain differently. Topcoat with 2–3 coats of polyurethane (sanded between with 320). Allow full cure (24 hr) before the family uses the stair.
- 5
Final wax / polish.
For high-touch stain runs, finish with a clear wax or polish over the cured topcoat. The hand-feel is the difference between a custom rail and a contractor rail — the wax is part of how UWP's shop rails feel in showrooms.
15 · Sign-off · Checklist + troubleshooting
Before the AHJ walks the job
Final inspection.
- Handrail height 34"–38" plumb above nosing, full length of flight (R311.7.8.1)
- Handrail continuous from top to bottom riser line (R311.7.8.2)
- Handrail grasp meets Type I or Type II per R311.7.8.3
- Handrail terminates in newel or returns to wall via rosette (R311.7.8.4)
- 1-1/2" minimum clearance between handrail and wall
- Stair guard ≥ 34" measured from the tread nosings (R312.1.2)
- Landing / floor-opening guard ≥ 36" where the walking surface is more than 30" above the floor (R312.1.1, R312.1.2)
- 4" sphere cannot pass between balusters (R312.1.3)
- 6" sphere cannot pass at the triangular space at the bottom of the guard
- Newel anchors resist 200-lb concentrated load (R301.5)
- All rail-bolt access mortises plugged and finished

