Skip to main content
Unique Wood Products

Custom Retro-Fit Pie-Shaped Tread

Renovation overlay for an existing winder — trapezoidal plan with the same 1" nose over a 5/8" body.

  • Instant estimate
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Loading configurator…
Where a retro-fit pie tread goes

Cap the winder
you already have.

The winders in an existing stair turn are where renovations stall — each one is a different trapezoid, and pulling them means demolition. The retro-fit pie drops a solid hardwood overlay over the winder that is already there: the same L-shape underside as our straight retro-fit treads, cut to the winder's shape.

  1. Measure the existing winder along its nose

    Front-edge length from the inside of the turn to the wall, on the tread that is already in place.

  2. Then both sides, square off the nose

    Left depth at the inside of the turn, right depth at the outside, as you face the stair from below. The overlay's back edge follows the slant.

  3. The lip does the rest

    The 5/8" body sits on the old tread and the built-up 1" nose wraps its front edge — no demolition, and the turn reads like new solid treads.

  4. Curved stairs too

    A radius stair is winders all the way up. Price each existing tread from its nose length and two side depths; the overlay is cut to its template.

  5. Open side? Return the end

    Where the outside of the turn is open, the winder runs 1-1/4" past the stringer and a mitered returned end carries the nose around the corner — no raw end grain shows.

Where a pie-shaped tread goes and how to measure itPlan view of an L-shaped stair turn with no landing: two standard treads run into three winder treads that fan around the inside corner, then two more standard treads leave at a right angle. The first winder is highlighted. A second plan shows a curved staircase, where every tread in the quarter turn is a winder fanning from about 8 inches at the inside wall to about 19 inches at the open side. A third drawing shows the highlighted L-turn winder as a trapezoid with its three measurements labelled: the front edge along the nose, the left depth at the inside of the turn, and the right depth at the outside wall, both measured square off the nose. A fourth drawing shows the returned end used on an open staircase: the tread runs 1-1/4 inch past the stringer and a mitered returned end carries the nose around the corner.PLAN · L-TURN WITHOUT A LANDINGThree winders carry the turn — each one a different trapezoid.newel11-1/2"standard tread~29" deepat the outside wall~8" deepat the inside of the turnUPDrawn to scale · 36"-wide stair · 3 winders at 30° · standard treads either sidePLAN · CURVED STAIROn a radius stair every tread is a winder — each one its own pie.11-1/2"standard tread~19" deepat the open side~8" deepat the inside wallDrawn to scale · 44"-wide stair · 30" inside radius · 15° per winderHOW TO MEASURE · THE THREE NUMBERSThe highlighted L-turn winder, as the configurator asks for it.A curved-stair tread is priced the same way; its template sets the curve.back edge · cut to your template36" · front edge (nose)measured along the nose, inside to outside8"left depth29"right depthEnlarged 1.5× · depths are taken square off the nose, not along the slanted back edgeTHE MITERED RETURNED END · OPEN STAIRCASEOne side of the stair meets a wall; the other is open, so that end shows.The mitered returned end wraps the nose round the open end so no raw board end shows.1 · FROM ABOVEWALL SIDEclosed endcut square,butts the skirtBACKsits against the riser — the upright board of the step aboveFRONT · THE NOSEthe rounded edge you step overoutside face of the stringer(the board the treads sit on)1-1/4"OPEN SIDEno wall — you can seethis end of every stepmitered returned enda 1-1/4" piece with the samenose, fixed to the end so thenose turns the corner andthe raw board end is hidden.It runs 1-1/4" past the back,behind the riser above.2 · STANDING BESIDE THE OPEN SIDEThe same tread seen from the room, looking at its open end.FRONT · THE NOSE← the tread carries on to the wall sideBACK · against the riserOPEN SIDEthe mitered returned endthe same nose, wrappedround the corner — no rawend of the board showingMeasure: wall to the outside face of the open stringer, plus the 1-1/4" returned end.Not reversible: it has a top and a bottom — tell us which side is open.In the configurator: tick Left or Right return. The L-shape body is handed.
Top: an L-shaped turn in plan — standard 11-1/2" treads either side, three winders fanning around the newel, the first one highlighted. Middle: a curved stair, where every tread in the turn is a winder. Below: that winder as the configurator asks for it — front edge along the nose, left and right depths square off it, back edge cut to template.
UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the stair disappears into the room instead of fighting it.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Core catalog
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Core catalog
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Specifications

The full spec sheet. For the builder who scrolled this far.

Body1" solid or 5/8" retro-fit
Edge profilesBullnose · eased · mitered returned ends
ConstructionEdge-glued solid — never veneered
SpeciesFive configured hardwoods
DimensionsAny width, depth & length to spec
GeometrySquare, pie, winder, curved, landing
MilledIn-house in Houston, TX
SurfaceUnfinished, sanded
Lead timeConfirmed at quote
Minimum order1 piece
TemplatingOn-site for curved & complex
QuotePlanning estimate in the configurator
Popular wood species

The species we run most.

Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.

Red Oak
Core catalog
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Core catalog
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

Can a winder be refaced without rebuilding the turn?
Usually yes. The retro-fit pie tread is the same overlay idea as a straight retro-fit — a full 1″ nose over a 5/8″ body — cut to the trapezoid of the existing step. The framing, the stringers and the turn itself stay where they are; you are capping what is already there.
How do I template an existing winder?
Do not rely on three numbers. Strip the step back to bare wood, then make a physical template — thin ply, hardboard or stiff card cut and scribed to the actual step, marked with which edge is the nose and which side is open. Winders in an existing house are rarely true trapezoids: the walls are out of square and the turn was framed to fit. A template captures that; a tape measure does not.
What if the winder is curved or irregular rather than a clean trapezoid?
Send the template anyway. A curved or bellied front edge can be cut, but it has to be drawn from the real step rather than described, and the nose has to be worked around the curve. Say on the quote request that the edge is not straight so the geometry is priced and planned rather than discovered at the saw.
What happens where the winder meets the newel?
The tread is notched around the post. Mark the post position and size on the template, because the notch has to be cut before the nose is finished and it changes how the return is handled on that end. If the post is being replaced as part of the job, decide the new post size first.
Do all the treads in the turn have to match?
They have to match in species, profile and finish, and they will not match in shape. Each winder in a turn is its own trapezoid, so order them as a set with each step templated and numbered. Number the templates to the steps and keep the numbering on the delivered treads — three similar trapezoids are very easy to mix up on site.
All answers →

Terms used on this page