Skip to main content
Unique Wood Products

Custom 8070 Pie-Shaped Tread

Trapezoidal solid hardwood tread for winders and turns — one front-edge length, two independent side depths. Priced on the trapezoid area.

  • Instant estimate
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Loading configurator…
Where a pie-shaped tread goes

Built for the turn
in your staircase.

Where a stair turns a corner without a landing, the treads fan out — narrow at the newel, deep at the wall. Those are winders, and each one is its own trapezoid. This configurator prices one winder at a time from three numbers you can pull straight off the stair.

  1. Front edge, along the nose

    Measure the nose from the inside of the turn to the outside wall. That is the length.

  2. Left and right depths, square off the nose

    Left is the inside of the turn, right is the outside, as you face the stair from below. Set them equal for a rectangular pie; different for a winder.

  3. The back edge comes from your template

    UWP mills the slanted back edge to a field template or dimensioned CAD reviewed before production, so each winder lands tight to the riser above it.

  4. Curved stairs too

    On a radius stair every tread is a winder. Enter the nose length and the two side depths for a planning price; the exact curve comes from the on-site template.

  5. Open side? Return the end

    Where the outside of the turn is open, the winder runs 1-1/4" past the stringer and a mitered returned end carries the nose around the corner — no raw end grain shows.

Where a pie-shaped tread goes and how to measure itPlan view of an L-shaped stair turn with no landing: two standard treads run into three winder treads that fan around the inside corner, then two more standard treads leave at a right angle. The first winder is highlighted. A second plan shows a curved staircase, where every tread in the quarter turn is a winder fanning from about 8 inches at the inside wall to about 19 inches at the open side. A third drawing shows the highlighted L-turn winder as a trapezoid with its three measurements labelled: the front edge along the nose, the left depth at the inside of the turn, and the right depth at the outside wall, both measured square off the nose. A fourth drawing shows the returned end used on an open staircase: the tread runs 1-1/4 inch past the stringer and a mitered returned end carries the nose around the corner.PLAN · L-TURN WITHOUT A LANDINGThree winders carry the turn — each one a different trapezoid.newel11-1/2"standard tread~29" deepat the outside wall~8" deepat the inside of the turnUPDrawn to scale · 36"-wide stair · 3 winders at 30° · standard treads either sidePLAN · CURVED STAIROn a radius stair every tread is a winder — each one its own pie.11-1/2"standard tread~19" deepat the open side~8" deepat the inside wallDrawn to scale · 44"-wide stair · 30" inside radius · 15° per winderHOW TO MEASURE · THE THREE NUMBERSThe highlighted L-turn winder, as the configurator asks for it.A curved-stair tread is priced the same way; its template sets the curve.back edge · cut to your template36" · front edge (nose)measured along the nose, inside to outside8"left depth29"right depthEnlarged 1.5× · depths are taken square off the nose, not along the slanted back edgeTHE MITERED RETURNED END · OPEN STAIRCASEOne side of the stair meets a wall; the other is open, so that end shows.The mitered returned end wraps the nose round the open end so no raw board end shows.1 · FROM ABOVEWALL SIDEclosed endcut square,butts the skirtBACKsits against the riser — the upright board of the step aboveFRONT · THE NOSEthe rounded edge you step overoutside face of the stringer(the board the treads sit on)1-1/4"OPEN SIDEno wall — you can seethis end of every stepmitered returned enda 1-1/4" piece with the samenose, fixed to the end so thenose turns the corner andthe raw board end is hidden.It runs 1-1/4" past the back,behind the riser above.2 · STANDING BESIDE THE OPEN SIDEThe same tread seen from the room, looking at its open end.FRONT · THE NOSE← the tread carries on to the wall sideBACK · against the riserOPEN SIDEthe mitered returned endthe same nose, wrappedround the corner — no rawend of the board showingMeasure: wall to the outside face of the open stringer, plus the 1-1/4" returned end.Reversible: flip the tread over and the returned end swaps to the other side.In the configurator: tick Left or Right return under Nosing & Returns.
Top: an L-shaped turn in plan — standard 11-1/2" treads either side, three winders fanning around the newel, the first one highlighted. Middle: a curved stair, where every tread in the turn is a winder. Below: that winder as the configurator asks for it — front edge along the nose, left and right depths square off it, back edge cut to template.
UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the stair disappears into the room instead of fighting it.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Core catalog
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Core catalog
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Specifications

The full spec sheet. For the builder who scrolled this far.

Body1" solid or 5/8" retro-fit
Edge profilesBullnose · eased · mitered returned ends
ConstructionEdge-glued solid — never veneered
SpeciesFive configured hardwoods
DimensionsAny width, depth & length to spec
GeometrySquare, pie, winder, curved, landing
MilledIn-house in Houston, TX
SurfaceUnfinished, sanded
Lead timeConfirmed at quote
Minimum order1 piece
TemplatingOn-site for curved & complex
QuotePlanning estimate in the configurator
Popular wood species

The species we run most.

Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.

Red Oak
Core catalog
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Core catalog
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

What is a pie-shaped tread?
A tread that is wider at one end than the other — a trapezoid rather than a rectangle. It is what a staircase uses to turn a corner without a flat landing. Three of them commonly take a stair through ninety degrees, and each one is a different shape, so each is milled individually.
What measurements do you need?
One front-edge length and two side depths, one for each side, taken independently. The two sides of a winder are almost never the same and the difference between them is the whole point of the shape. Measure each tread in the turn separately, and take the front edge at the nosing line rather than at the back of the step.
How does code treat a winder tread?
Differently from a straight tread, because the depth changes across the step. The IRC measures the required tread depth at a fixed distance in from the narrow edge, and also sets a minimum depth at the narrowest point so the inside of the turn cannot come to nothing. Your local jurisdiction has the final say and may amend it. Confirm the geometry against the code in force before the treads are cut — a winder is expensive to re-cut.
Which side gets the return?
The open side, the same as on a straight tread. On a winder that is normally the wide end, where the stair faces the room. Mark it on the order as left or right looking up the stair, and say so explicitly — on a trapezoid the two ends are not interchangeable and a return on the wrong end is scrap.
How is a pie-shaped tread priced?
On the trapezoid area rather than on a rectangle around it, so you are not charged for the corner that gets cut away. That said, a winder takes more layout and more waste than a straight tread of the same footprint, which is reflected in the written quote.
All answers →

Terms used on this page