Skip to main content
Unique Wood Products

Stair terminology glossary — tread, riser, stringer, nosing, and the rest

A staircase has more named parts than most people realize. The tread is the horizontal walking surface; the riser is the vertical board between treads; the stringer is the diagonal structural framing; the nosing is the front lip of the tread; the skirt board is the trim against the wall. Below: every term, plain English, with a note on where each one matters for ordering and installation.

The short version

  • Tread — the horizontal walking surface. Riser — the vertical board between treads. Stringer — the diagonal structural framing.
  • Nosing — the front lip of the tread that overhangs the riser. Skirt board — the flat trim along the wall.
  • Newel — the heavy post at the top, bottom, or turn of the railing. Baluster — the slim vertical between treads and handrail.
  • Landing tread — narrow bullnose-front tread at the top of a stair. Stairnosing — the front-edge-only profile used with tile, carpet, or LVP on the step.

The full answer

A staircase has more named parts than most people realize — and the names get used inconsistently by manufacturers and DIY sites. Below is the working glossary of the terms UWP and serious finish carpenters use day-to-day, with notes on where each one matters for ordering or installation.

The walking surfaces

  • Tread — the horizontal board you step on. UWP’s 8070 (bullnose), 8071 (retro-fit), 8072 (square-edge), 8073 (square retro-fit) are the four standard tread profiles. Standard size: 1″ thick × 10-1/2″ to 11-1/2″ deep × 42″ to 96″ wide.
  • Riser — the vertical board between two treads. Hides the gap between the back of one tread and the front of the next. Standard size: 3/4″ thick × the rise height (typically 7″ to 7-3/4″).
  • Nosing — the front edge of the tread that overhangs the riser below. Required by code (3/4″ minimum) unless the tread is 11″+ deep. The visible front lip you see from below the stair.
  • Landing — a flat platform where a stair changes direction or pauses. The landing surface is built into the floor structure; UWP’s landing tread (8091 bullnose / 8090 square) finishes the front edge of a landing where it meets the next step down.
  • Stairnosing — a narrow front-edge profile (not a full tread) used when the rest of the step is tile, carpet, LVP, or laminate. The wood nose finishes the edge; the other material fills the rest of the step. See stair treads vs. stairnosing.

The structure

  • Stringer — the diagonal structural framing that the treads and risers sit on. Typically 2× lumber (2×10, 2×12). Hidden on closed-stringer stairs; visible and finished on open-stringer stairs.
  • Closed stringer — stair with walls on both sides; the stringers are hidden behind skirt boards.
  • Open stringer (housed stringer) — stair with one or both sides open; the stringer is itself a finished piece, with tread ends cut to fit notches or housings.
  • Skirt board — the flat trim running along the wall beside the stair, covering the rough ends of treads and risers. Standard thickness ~11/16″ on most carpeted stairs. See the skirt board question.
  • Substrate — the rough plywood or pine that sits between the stringer and the finished tread. Re-treads happen here.

The railing

  • Newel — the heavy post at the top, bottom, or turn of the railing. The structural anchor of the handrail. Sometimes called a newel post.
  • Handrail — the horizontal (or angled) rail you grip while walking the stairs. Code requires: at least one side, 34″ to 38″ above the nosings, graspable profile.
  • Baluster — the slim vertical between the handrail and the treads (or knee wall). Sometimes called spindle or picket. Spaced so a 4″ sphere can’t pass through (code minimum).
  • Balustrade — the entire railing assembly: newels, handrail, balusters, and bottom rail.
  • Knee wall (or pony wall) — a short wall between treads and handrail instead of balusters. The handrail sits on top of the knee wall.

Types of stairs

  • Straight-run — one continuous flight from bottom to top. The simplest geometry.
  • L-stair — straight-run with one landing and a 90° turn. Common in residential layouts.
  • U-stair — straight-run with one landing and a 180° turn. Common in stairwells where the stair returns above itself.
  • Winder stair — a turn made without a landing; tapered treads pinwheel around the corner. Higher risk of out-of-code geometry.
  • Spiral stair — a continuous helix around a center pole. Code allows tighter geometry than other stairs.
  • Curved (radius) stair — a stair that follows an arc, not a hard angle. Each tread is a unique shape, templated on-site. See curved stair treads.
  • Floating (open-rise) stair — no risers; the treads cantilever or hang from a single stringer. Modern architectural style.

Returned ends and special shapes

  • Returned end — when a stair has an open end (visible from the side), the bullnose continues around the side of the tread so no raw end shows. UWP mills returned ends on one or both ends as a configurator option.
  • Pie / winder tread — a tread that fans out to fit a turn in the stair. Wider at the outside of the turn, narrower at the inside. Code requires a minimum tread depth at the walking line (typically 12″ from the inside of the turn).
  • Bullnose tread (also called bullnose starting step) — terminology overlap: "bullnose" can mean the rounded front edge of any tread OR a specific stair part — the curved decorative starting step at the bottom of a stair. Context tells you which.
  • Flared start — a starting step that flares out wider than the rest of the stair. Common decorative move on traditional homes.

Profile and edge terms

  • Bullnose — rounded front edge. The most common tread profile in traditional and transitional homes.
  • Square edge — a straight, sharp front edge. Modern look.
  • Eased edge — slightly rounded square edge, softer than square but not bullnose. The compromise option.
  • Waterfall edge — a tread where the front face wraps around and continues vertically — sometimes used on thick treads to read as a continuous slab. Aesthetic.

Code terms (IRC and beyond)

  • Rise — the vertical distance from one tread surface to the next. Code max: 7-3/4″.
  • Run — the horizontal distance from the nosing of one tread to the nosing of the next. Code min: 10″.
  • Walking line — the imaginary line where most foot traffic occurs, typically 12″ from the inside of any turn. Used to measure tread depth on winders.
  • Headroom — the vertical clearance above the stair. Code min: 6′8″.
  • Egress stair — a stair that serves as a required exit path. Subject to additional code requirements on commercial buildings.

Where each term matters for ordering

When you order…You need to confirm…
TreadsWidth, depth, thickness, profile (bullnose / square / eased), species, returned ends yes/no
RisersThickness, height, species, painted vs. stained
Landing treadsWidth, profile, matching species and thickness to your floor
StairnosingThickness matched to the finished floor on the steps (typically 5/16″, 3/8″, 1/2″, 9/16″)
Skirt boardsTotal rise, total run, number of treads — we mill to length, you cut on-site
Custom curved treadsOn-site templating appointment — no measurements alone work

Use this glossary as a shared vocabulary with your installer, finisher, and supplier. Confusing tread for stairnosing, or skirt for stringer, leads to the wrong product on order. Bring photos to the Tanner Rd yard if any term doesn’t click — we’ll walk through what you have.

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-05-27