
PoplarPaint-Grade · Most Popular
Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.
1-1/4" × 1-1/4" — milled to order at NW Houston / Tanner Rd in Primed FJ Pine, Red Oak, White Oak, Maple, Pine, Knotty Alder, Primed MDF, Flex, or ground to match an existing profile.
Primed FJ Pine · 1-1/4" × 1-1/4"
Cove Moulding · Full-length stick
PROFILE
UW85
priced by the piece on your quote
The UW85 cove moulding profile in 1-1/4" × 1-1/4" — run to order in solid hardwoods, paint-grade primed, and MDF.
Cove Moulding · Special order · Custom milling available
Colour is indicative — grain and colour vary board to board.
A stocked profile runs one size off one knife. Length is a quantity, not a dimension — order by the piece.
Need this section at another height, in another species, or ground to match an existing profile? That is a custom run — send us a sample or an offcut.
Order by the code above at the Tanner Rd counter. Pricing, availability and lead time are confirmed on the quote.
PROFILE
UW85priced by the piece on your quote
Specification · UW85
Primed FJ Pine · 1-1/4" × 1-1/4" · Cove Moulding
Stocked profiles run primed for paint; in solid wood this one is milled to order, so the species is your choice rather than whatever is on the shelf. These are the five we run most for cove — pick one in the swatches above to see this profile in it.

Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.

Best for — The workhorse match for red oak floors — the most-stocked species across treads and moulding.

Best for — Cooler, modern, wire-brushed and natural finishes; the premium choice for light contemporary work.

Best for — Pale contemporary work, maple cabinetry, and anywhere an even near-white tone is wanted.

Best for — Dark, high-end interiors and feature work where a rich chocolate tone is the statement.
A finished cove moulding profile for trim, panel, and millwork detailing.
Primed FJ pine and MDF for paint; solid Red/White Oak, Maple, Pine, and Knotty Alder for stain.
Coordinates with matching base, casing, and crown for a consistent millwork program.
Match an existing profile or run a custom length — our mill cuts to spec.
Crown moulding is sprung — it sits at an angle bridging the wall and ceiling, with an ornate profile that can include curves, beads, and steps. Cove moulding is a single concave curve, sitting flat into the wall-ceiling corner. Crown reads as traditional and substantial; cove reads as clean and quieter. For 8-foot ceilings, cove or small crown. For 9-foot+, scale up.
Read the answer →Cabinet crown molding sits on top of upper cabinets, finishing the cabinet-to-ceiling transition. Room crown moulding runs along the wall-ceiling seam around the rest of the room. These two crowns typically don’t coexist in the same kitchen — the cabinet crown is the dominant ceiling treatment when present, and room crown would visually compete. Use cabinet crown in kitchens with upper cabinets that reach close to the ceiling; use room crown elsewhere.
Read the answer →Calculate baseboard by measuring the perimeter of every room, subtracting door openings, then adding 10% for waste. Casing needs 17 to 20 linear feet per standard door, 14 to 17 per window. Crown takes the same perimeter as base. Shoe and quarter round match the base. The trim and casing calculator on our site does the math by room — feed in dimensions, get a total order list.
Read the answer →Yes. UWP runs custom knives to match existing baseboards, crown, casing, and any other milled profile. Bring us a 6-inch sample piece, a clean sketch with dimensions, or even a photo with a scale reference. We grind a new knife to match, run your order, and keep the knife on file for re-orders. One-time knife fee covers the setup; per-foot pricing matches our stock catalog.
Read the answer →