
PoplarPaint-Grade · Most Popular
Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.
3" / 3-1/4" / 3-1/2" / 4" x 1-1/16" — milled to order in Houston. One knife, 4 heights, so the profiles stack and mitre together on the same job.
Dimensions are nominal. Milled profile is held to ±1/64″ and length to ±1/16″ — tolerances and how each is measured. Hold a sample before you commit a run.
White Oak · 3" × 1-1/16"
Casing · Chamfer · Plain
ORDER CODE
UW10549-30
quoted by the linear foot
Colour is indicative — grain and colour vary board to board.
Others on request — send us a sample or an offcut and we will match it.
One knife, 4 widths. Length is a quantity — quoted by the linear foot.
The moulded detail is identical across 3", 3-1/4", 3-1/2", 4" — only the flat field changes, so the profiles stack and mitre together on the same job.
The DXF is the finished section, in inches, for drawing reference. To match an existing profile instead, send us a sample or an offcut and we will grind a knife to it. Knife, setup and shop charges are on the custom moulding price schedule.
ORDER CODE
UW10549-30quoted by the linear foot
Specification · UW10549
White Oak · 3" width × 1-1/16" · Casing
Rendered from this profile's own section — the same geometry as the spec sheet and the DXF, not an illustration of something similar.

Every profile in the library is milled to order, so the species is your choice rather than whatever happens to be on the shelf. These are the five we run most for casing — pick one in the swatches above to see this profile in it.

Best for — Our highest-volume species. The value choice for painted trim, casing and built-ins — a lower-cost paint-grade hardwood for any profile finished in colour, not stain.

Best for — The workhorse match for red oak floors — the most-stocked species across treads and moulding.

Best for — Cooler, modern, wire-brushed and natural finishes; the premium choice for light contemporary work.

Best for — Pale contemporary work, maple cabinetry, and anywhere an even near-white tone is wanted.

Best for — Dark, high-end interiors and feature work where a rich chocolate tone is the statement.
Three casing styles cover most American homes: colonial (stepped profile, traditional, the default since the 1950s), craftsman (flat board with a simple cap, square-edged, bungalow and arts-and-crafts homes), and modern square (a flat rectangle, no profile, contemporary and minimalist). Pick by the era and architecture of your home — don’t mix styles between the casing and the baseboard.
Read the answer →Trim choice should read as a consistent system across the house, not a room-by-room patchwork. Baseboard and casing run everywhere, sized to ceiling height and door scale. Crown is reserved for formal rooms in traditional homes and skipped in modern ones. Chair rail and panel mould go in formal dining and entry. Stair trim ties the upstairs and downstairs together.
Read the answer →Paint-grade stock is chosen for a flat, even surface that disappears under primer — grain, colour and small defects do not matter because nothing will show. Stain-grade stock is chosen for its face: colour, figure and grain continuity across a run. Poplar is the paint-grade default because it machines cleanly, holds a crisp profile edge and takes primer well.
Read the answer →Yes. UWP runs custom knives to match existing baseboards, crown, casing, and any other milled profile. Bring us a 6-inch sample piece, a clean sketch with dimensions, or even a photo with a scale reference. We grind a new knife to match, run your order, and keep the knife on file for re-orders. One-time knife fee covers the setup; per-foot pricing matches our stock catalog.
Read the answer →