1 · Before You Begin
A stair guard, not a decoration
Iron carries the guard load.
A baluster is the vertical infill between the handrail and the tread that turns a stair rail into a code-compliant guard. Iron does this work mechanically — the baluster is set into the rail above and the tread below with structural epoxy, and the matched shoe hides the joint. No nails, no screws, no shoe-mounted set-screws as the primary fastener.
Iron balusters also carry a visual job. The shape (plain, twist, basket, star, rectangle, industrial) and finish (Satin Black, Antique Bronze, Oil Rubbed Bronze, Oil Rubbed Copper, Silver Vein) set the tone of the staircase before the first piece of furniture arrives. Plan the rhythm — 1-in-3 or 1-in-4 accent balusters between plain shafts — before you order, so the staircase reads finished, not busy.
- Verify finish across every shape — SB is most common, but the AB / ORB / ORC / PC lines exist by shape, not by job.
- Confirm rod size (9/16" or 1/2") drives the drill bit & shoe — do not mix sizes in one run.
- Count plain vs. accent balusters before the first cut and lay them in the planned rhythm.
- Order one EPOXY bottle per ~30 balusters — short-shipping epoxy stops the install.
Figure in the PDF: Anatomy of an iron baluster
Three regions, one part.
Top square end – ~1" mortise into the underside of the handrail. Cut here to fit rail height.
Shaft – hammered or twisted along 36"–38" of length, sometimes interrupted by a cast detail (star, basket, rectangle).
Bottom square end – 1-1/2" mortise into the tread, hidden by the flat or rake shoe that sits on the tread surface.
2 · The Iron Baluster System
What you’re installing
One system, every shape and finish.
The UW M-series — UW-M673 / M674 / M301–M304 and the rest of the line — is built around two interchangeable rod sizes (9/16" and 1/2" square) and matched finishes. The star-medallion and rectangle shapes ship in Satin Black only; other shapes add Oil Rubbed Bronze, Oil Rubbed Copper or Silver Vein by profile.
- UW-M673 Single Star
- 9/16" Sq · SB
- UW-M674 Double Star
- 9/16" Sq · SB
- UW-M301 Single Rectangle
- 1/2" Sq · SB
- UW-M302 Double Rectangle
- 1/2" Sq · SB
- UW-M303 Triple Rectangle
- 1/2" Sq · SB
- UW-M304 Industrial
- 1/2" Sq · SB
Satin Black (SB) · Antique Bronze (AB) · Oil Rubbed Bronze (ORB) · Oil Rubbed Copper (ORC) · Silver Vein (PC). The full set runs on every plain, twist, basket, and rectangle shape; star-medallion shapes ship in Satin Black only.
3 · Tools & Field Order
Set up for a clean install
The right bit, the matched shoe.
- Cordless drill — hammer-drill optional for hardwood treads
- 9/16" or 1/2" brad-point or Forstner bit (matched to baluster rod size)
- 3/8" spade bit for handrail mortises (centered in rail)
- Iron-baluster construction adhesive (EPOXY · CSD 1034793)
- 4-foot level, 6" torpedo level, plumb bob
- Tape measure, combination square, pencil
- Painter’s tape — mask the shoe-line on the tread before drilling
- Hacksaw or 14 TPI metal-cutting bandsaw blade — to trim top end to rail height
- Mineral spirits + rag for epoxy clean-up before it cures
A polyurethane construction adhesive can substitute for the iron-baluster epoxy in a pinch — the listed EPOXY is the spec’d product and what every UWP-supplied job ships with.
Every job needs the epoxy plus three matched shoes per baluster line: a flat shoe at the level run, a rake shoe at the stair angle, and an adjustable knuckle under the handrail. Order the rod size, finish, and shoe set together — the parts are not interchangeable across sizes.
UW-EPOXY · CSD 1034793
Iron-baluster adhesive – ~30 balusters / bottle
- UW-ALM06-LSB / UW-06-XX · Flat shoe
- UW-ALPSH02-LSB / UW-02-XX · Rake shoe
- UW-M798SB · Adjustable knuckle
XX = SB / AB / ORB / ORC / PC finish code
4 · Installation · Steps 1–2
Plan & lay out
The 4" sphere rules every layout.
- 1
Plan the rhythm before you cut
Decide the pattern — all plain balusters, or plain with accents. The standard accent rhythm is 1-in-3 or 1-in-4 (every third or fourth baluster carries the cast detail: star, basket, rectangle). Count the accents before the first hole goes in.
Mask a pencil line on the top of each tread and on the underside of the handrail where the shoe will sit — painter’s tape keeps the finish clean and gives you a target to mark to.
- 2
Lay out the spacing
IRC R312.1.3 — a 4-inch sphere must not pass between adjacent balusters (4-3/8" is allowed on the open side of a stair; 4" is the safe layout target). On a typical 10–11" tread, three balusters per tread, evenly spaced, holds the rule with room to spare.
Spacing formula: ((tread run − baluster width) / (n + 1)) · spacing center-to-center. With three 9/16" balusters on a 10" run, that is roughly 2-3/8" to 2-1/2" between shafts — well under 4".
Figure in the PDF: Three balusters per tread — the 4" sphere check between every adjacent pair
5 · Step 3 · Drill the mortises
Top first, then the bottom
Two holes. One straight line.
- 3
Drill the top mortise first
With the handrail set at code height (34"–38" to nosing on the rake, 36" minimum at the landing), mark each baluster center on the underside of the rail. A 3/8" hole × ~1" deep accepts the 9/16" or 1/2" square top end with room for epoxy.
Drop a plumb bob from each top hole and mark the tread. The plumb mark is where the bottom mortise goes — drill a 9/16" or 1/2" hole (match the rod) about 1-1/2" deep, square to the tread surface.
Drill before any balusters are set. Doing the rail and treads in one pass keeps the line plumb across the whole run.
Figure in the PDF: Mortise depths — ~1" top, 1-1/2" bottom
A · Post-to-post
Handrail meets the face of each newel. Drill the rail mortises between newels only — the newel sits in the layout but takes no baluster.
B · Over-the-post
Continuous handrail rides over the newels on turn-out and rake fittings. Drill the rail mortises across the full run, including over the newel.
6
Steps 4–5 · Dry-fit, epoxy & set
Dry-fit every baluster. Then commit.
With every mortise drilled, set the entire run dry first — no epoxy. This is where you catch a mortise drifted off plumb, a baluster cut too long, or a shoe in the wrong finish. Fix it before the epoxy locks anything in.
4 · Dry-fit & plumb
Drop each baluster bottom into its tread mortise and the top into the handrail. Hold a 6" torpedo level against the shaft and check plumb on both axes — front-to-back and side-to-side. Any baluster that will not seat plumb gets called out now; a mortise is far easier to re-drill before the epoxy cures.
If the top end is long, mark, pull the baluster, trim with a hacksaw from the top, deburr, and refit. Confirm the rail height (34"–38" from nosing) holds across the run.
Figure in the PDF: Dry-fit — plumb on both axes
5 · Epoxy & set
Work one baluster at a time. Fill the bottom mortise about half-full with iron-baluster epoxy, slide the matching shoe down over the shaft, drop the bottom into the epoxy, slide a bead of epoxy into the top mortise, then push the top into the handrail. Slide the shoe down to the tread, square it to the rail, and let the epoxy cure undisturbed for the manufacturer’s working time — usually 30 minutes to tack, 24 hours to full strength.
Figure in the PDF: Stage 1 · epoxy in mortise
Figure in the PDF: Stage 2 · set baluster
Figure in the PDF: Stage 3 · slide shoe down
7 · Step 6 · Shoes & final set
Match the angle & the finish
Three shoes per baluster line.
Every iron baluster on a residential staircase needs three shoes: a flat shoe on the level run, an adjustable rake shoe on the stair pitch, and a top knuckle / shoe under the handrail. The shoes match the rod size (9/16" or 1/2") and the finish of the baluster — verify both before set.
UW-ALM06-LSB · Flat shoe
The square shoe block that sits flat on a level run — landing tops and level upper guards. Set with the optional set-screw on the back side facing the wall, not the room.
UW-ALPSH02-LSB · Rake shoe
Angled shoe whose face matches the stair pitch so it sits flush on the tread at the rake. Order it in the same rod size and finish as the baluster.
UW-M798SB · Adjustable knuckle
The collar that caps the baluster at the underside of the handrail. Hides the top mortise and gives the rail-to-baluster joint a finished shadow line.
8 · Variants · Knee Wall & Wood
Two installs that change the detail
When the rail is not over a tread.
Knee-wall (pony wall)
On an open stair with a half-height knee wall replacing the open guard, the baluster sets into a wood cap on top of the wall instead of the tread itself. Drill the cap to mortise depth (~1"), set with epoxy, finish with the same flat shoe as a level run. The cap thickness is included in the rail-height math — measure from the cap face, not the wall framing.
Wood balusters
Turned wood balusters use a 1/2" or 5/8" dowel pin at the bottom (preformed on the baluster) into a matching tread mortise, and a top end glued into a round hole in the handrail. No shoes — a wood fillet between balusters spans the rail underside instead. Same 4" sphere rule applies.

