1 · Foreword · Scope & system
When the rail has to turn
The kerfed rail does the bending.
Pre-engineered bending handrail is a standard hardwood handrail profile with a series of vertical kerfs cut into the underside. The kerfs let the rail flex around a curve where a solid rail would crack or refuse to bend. Glue closes the kerfs when the rail is clamped into its final shape; once cured, the rail behaves like a solid section. This guide covers the field install — layout, template, dry-fit, glue-up, and finish — for the bending rails UWP stocks at Tanner Rd.
2 · Anatomy · How bending rail works
A handrail that takes a curve
The kerf is the mechanism.
Figure in the PDF: BENDING RAIL · cross-section showing kerf pattern
Figure in the PDF: KERFS OPEN WHEN STRAIGHT · CLOSE WHEN BENT INWARD
3 · Catalog · Bending rails offered
What UWP offers
The bending rail program.
UWP offers the bending versions of the same profile families as the straight handrails — 6010, N6210, 6710, and 6003. Same profile family means a curved-to-straight transition is clean: the cross-sections align within thousandths and the joint disappears under finish. Bending rail is special order; species, BSP / BM variants and timing are confirmed at quote.
- UW-6010B
- 6010 bending rail (red oak)
- Most common
- UW-WO6010B
- 6010 bending rail (white oak)
- WO species
- UW-N6210B
- Narrow 6210 bending rail (RO)
- Tighter grip
- UW-WON6210B
- Narrow 6210 bending rail (WO)
- WO species
- UW-6710B
- 6710 bending rail
- Larger profile
- UW-6003B
- 6003 bending rail
- Small profile
- UW-WO6003B
- 6003 bending rail (WO)
- WO species
BSP suffix = special prep (additional kerfing for tighter radii). BM suffix = bend matched (kerf-pattern matched to a specified radius — special order, lead time applies).
- UW-6007
- Sub-rail (6007)
- Most common
- UW-WO6007
- Sub-rail (WO)
- WO species
- UW-6007A
- Sub-rail — alt profile
- Variant
- UW-6045
- Plowed sub-rail
- Square balusters
- UW-6050
- Sub-rail — deep profile
- Tight radii
- UW-6000F
- Finger-jointed sub-rail
- Paint grade
- UW-6001SP3
- Special-prep sub-rail
- Pre-kerfed
- UW-6001FP3
- FJ special-prep sub-rail
- Paint, pre-kerf
Bending rails come in 6', 8', 10', and 12' lengths. For a curved-stair run, order one length longer than the developed arc length — bending consumes ~3–5% in kerf closure.
4 · Method selection · Radius tiers
How tight is the curve?
Pick the method by radius.
The single decision that drives the whole install is the radius. Measure (or estimate from the plan) the inside radius of the curve at handrail height. The radius determines whether a single bending rail handles it, whether you need a sub-rail underneath, or whether the curve calls for a shop-laminated section.
Figure in the PDF: TIER 1 · EASY (R > 60")
Figure in the PDF: TIER 2 · MEDIUM (24"–60")
Figure in the PDF: TIER 3 · TIGHT (R < 24")
5 · Tools · Materials · Adhesives
Set up the curve before you cut the rail
Tools & materials.
- Story stick — straight 1x scrap longer than the developed arc length
- Trammel arm + pencil — for stepping off the radius if drawing the curve from scratch
- Long flexible curve gauge or 6-ft contour gauge (a long PVC strip works)
- Spring tape + folding rule for in-place arc measurement
- Sharp pencil; carpenter's crayon for rougher marks
- Compound miter saw — clean transition cuts to straight sections
- Fine-tooth handsaw or Japanese pull saw — for trim cuts on the bench
- Sharp 3/4" chisel for trimming kerf strips after cure
- Block plane + sanding sponge (120, 180, 220) for joint and curve refinement
- Long-throat bar clamps OR pipe clamps — minimum 12 around the curve length
- Cauls — shop-made wood strips, 1/2" plywood the rail width — protect rail face from clamp jaws
- Strap clamps (1") for landing turns and volutes
- Spring clamps for small detail work
- Slow-set wood glue — minimum 30-minute open time (Titebond Extend, Original is too fast)
- Polyurethane glue (Gorilla Glue or equivalent) — moisture-cured, gap-filling, longer working time
- Epoxy (slow hardener) — for tight-radius / structural critical joints
- Construction adhesive — only for sub-rail to substrate; not for the bending rail itself
Slow-set PVA (Titebond Extend) is the workhorse for Tier-1 and Tier-2 radii. Get more open time so you can fully position and clamp before set. PU is the choice for tight radii where you need foam-fill in the closing kerfs. Epoxy when the curve is structural and you cannot afford a re-do.
- UW-6007 sub-rail (most common), or UW-6045 if balusters are square + plowed
- 1-1/4" finish screws — sub-rail to structure (every 8")
- Rail-bolt kit — for curved-to-straight rail transition (UW-6010B → UW-6010)
- Color-matched wood plugs (per species)
- Pin nails (23 ga) for clamp-time positioning, not structural
6 · Layout · Templating the curve
Field-measure before you cut
Build the template first.
Architectural drawings rarely match the as-built curve. Before cutting a single inch of bending rail, capture the real curve with a story stick. A flexible strip of stock laid along the actual installed sub-stair or landing curve gives you the developed arc length plus the chord-and-sagitta geometry — the two numbers that tell you exactly how much rail to cut and what radius you're actually bending to.
Figure in the PDF: STORY STICK + CHORD/SAGITTA — captures the real curve
- 1
Lay the story stick.
Use a flexible 1/4"–1/2" strip of stock longer than the developed arc length. Bend it gently into the curve at handrail height (typically 36-1/2" plumb above the nosing or landing). Pin it temporarily with brad nails or tape.
- 2
Mark the endpoints + midpoint.
Mark on the story stick exactly where the curve begins (transition from straight) and where it ends. Mark the midpoint. These three reference points carry through to the rail layout.
- 3
Capture chord + sagitta.
Pull the story stick off the curve and lay it flat. Measure the straight-line distance from start to end (chord). Re-bend to the curve and measure the height from the chord to the midpoint (sagitta). Record both. These are the curve fingerprint.
- 4
Compute radius, transfer to rail.
Use the formula above to compute the effective radius. Cross-reference to the radius tier (page 5) to confirm the method. Then mark the bending rail at the same start/midpoint/end positions you marked on the story stick — these become the dry-fit reference points.
7 · Install · Dry-fit verification
Never glue without dry-fitting first
Dry-fit first.
Bending rail glue-up has no second chance. Once glue is open and the rail is clamped to the curve, any mismatch in length, alignment, or rail-bolt position has to be lived with. Dry-fit confirms the rail takes the bend cleanly, lands on the marks, and joins to straight sections at the right plumb cut — all before glue touches a surface.
- 1
Bend the rail dry to the curve.
With the sub-rail in place (Tier 2 or 3) or against the curved framework (Tier 1), bend the bending rail by hand to follow the curve. The rail should follow the radius without forcing — your hand pressure should bend it the last quarter of the way, not muscle the whole bend. If the rail resists strongly at any point, the radius is tighter than the rail can take. Stop; reconsider method.
- 2
Verify reference marks.
With the rail bent in place, check that the start, midpoint, and end marks on the rail land on the corresponding marks on the curve. Off by more than 1/4"? The rail length is wrong or the curve length is. Re-measure the story stick, recut if needed. Off by less than 1/4"? Adjust by trimming one end — bending shortens the rail by ~3–5% in kerf closure.
- 3
Test clamp positions.
Set every clamp dry — pipe clamps spaced ~6"–8" around the curve length, cauls between the clamp jaw and the rail to spread pressure. Light pressure only at this stage. Walk the curve and verify every clamp can apply pressure perpendicular to the rail face (not at an angle). Mark caul positions in pencil so they go back exactly.
- 4
Check the cross-section transition.
Where the bending rail will join the straight rail, hold a sample of the straight rail (same family) up to the bending rail end. Cross-sections must match — same height, same width, same profile curvature. If they don't, you have either the wrong family or a sanded-down face. Recut the joint, plane to match, or order the right family.
- 5
Disassemble in reverse order.
Release clamps one at a time from the ends toward the middle (reverse of the install order). Lift the rail away clean. Mark the clamping order on the cauls or the back of the rail so you re-install in the same sequence when glue is on.
8 · Install · Glue-up & clamping
Open time is the constraint
Glue, bend, clamp.
Two people, ideally three for anything longer than 4 feet. Glue applied to every kerf face (both sides) plus the kerf top. Rail bent into the curve. Clamps tightened in sequence from one end to the other, then incrementally cinched. Cure 24 hours minimum before unclamping.
Figure in the PDF: RADIAL CLAMP PATTERN — 6"–8" SPACING
- 1
Glue every kerf.
Stand the rail flat on the bench, kerfs up. Apply slow-set PVA into every kerf with a thin nozzle bottle. Don't skimp — kerfs that close on a dry interface will fail at the joint. Coat the kerf top face (the underside of the rail above the kerf) lightly. 30 minutes of working time starts now.
- 2
Bend into the curve.
Two people: one at each end of the rail. Lift the rail onto the curve, kerfs facing in (concave). Walk it into position so the start mark lands on the start mark on the curve. Press the midpoint into place.
- 3
Clamp from the ends in.
Set the first clamp at one end of the curve, light pressure. Second clamp at the opposite end, same pressure. Walk inward from both ends, setting clamps one at a time at 6"–8" spacing. Cauls under every jaw. Final clamp at the midpoint.
- 4
Tighten in sequence.
With all clamps lightly set, walk the curve and incrementally tighten each clamp. Two passes minimum — first pass to firm pressure, second pass to full. Watch for glue squeeze-out at every kerf — that tells you the kerf is closing fully. No squeeze-out = no glue contact = future failure.
- 5
Clean and cure.
Wipe glue squeeze-out with a damp rag while still wet — set glue is much harder to remove. Once clean, leave undisturbed for a minimum of 24 hours (longer for low temperature or high humidity). Do not test the cure by flexing — wait. After 24 hr, release clamps in reverse order (midpoint last, ends first).
9 · Method · Sub-rail (Tier 2+)
Two layers, more control
Sub-rail + bending rail.
On a Tier-2 or Tier-3 curve, the sub-rail does the structural bending and screws to the substrate; the bending handrail laminates to the sub-rail as a finish skin. The sub-rail bends in one direction; the bending rail bends in the same direction. Together they hold the curve under load without spring-back.
Figure in the PDF: SUB-RAIL CROSS-SECTION · bending rail laminated on top of sub-rail
- 1
Install the sub-rail.
Use UW-6007 (most common) or UW-6045 if the rail is plowed for square balusters. The sub-rail is itself a kerfed bending stock — flex it to the curve, hold dry first to verify fit. Screw to the substrate (curved knee wall, curved framing, or curved template) with 1-1/4" finish screws every 8". Counter-bore the screw heads for later concealment.
- 2
Verify sub-rail geometry.
Once the sub-rail is fastened, check that the top surface tracks the desired handrail line at the right plumb height. The bending rail will follow this surface exactly — adjust here before laminating the top rail.
- 3
Apply glue to sub-rail top.
Spread slow-set PVA evenly across the entire top surface of the sub-rail. Generous bead — the bending rail will press it into a thin uniform layer when clamped. Avoid puddling in the middle.
- 4
Glue and bend the top rail.
Follow the same kerf-glue sequence as page 9 — glue every kerf, walk the rail onto the curve, clamp from the ends inward. The sub-rail acts as the curved surface; the bending rail follows it.
- 5
Cure, plug, finish.
Cure 24 hr. Release clamps. Plug the sub-rail screw counter-bores with matching species. Sand the joint between sub-rail and bending rail with 220 grit — they should read as a single profile. Touch-up putty as needed.
10 · Cases · Landings & volutes
Most curve jobs are not curved stairs
Landing turns and volutes.
A continuous-radius curved stair is one application. Most curve jobs are smaller — a landing where the rail turns 90°, a volute at the bottom of a straight flight, or a curved starter step. Same product, same method, smaller scale. The radius is usually tighter on these (Tier 2–3) so plan on sub-rail + careful glue-up.
Figure in the PDF: LANDING TURN · 90° rail rotation
Figure in the PDF: VOLUTE · tight spiral at starter step
- 1
Landing turn layout.
A 90° landing turn typically has a radius of 8"–12" measured at the rail centerline. Always Tier 3 — install a sub-rail (UW-6007 or 6045) following the inside corner of the landing. Glue the bending rail over the sub-rail in a single clamping pass. The transitions to straight rail on both ends use rail bolts.
- 2
Volute layout.
A volute (starter swirl) is the most demanding curve on a typical job — radius often under 6". Site-bending is rarely the right method here. Two options: (1) the volute is supplied as a pre-shaped fitting from the manufacturer matched to the rail family; (2) UWP's shop laminates the volute from the same species to template. The bending rail in the rake-section above the volute joins the volute fitting with a rail-bolt.
- 3
Curved starter step.
A curved starter step (round bullnose at the bottom riser) often has the rail following the same curve at handrail height. Typical radius 12"–20" — Tier 2 with sub-rail. The starting newel sits at the end of the bullnose; the bending rail terminates into the newel face.
11 · Joinery · Curve to straight transition
The transition that has to disappear
Curved meets straight.
On any stair with both straight and curved rail, there's a transition joint where the bending rail meets a straight handrail. Done right, it's invisible from above — same profile family, same species, same finish, joined with a rail bolt the same way two straight sections would meet. The trick is the cut: the bending rail must be cut perpendicular to the rail axis at the exact point the curve starts.
Figure in the PDF: TRANSITION JOINT · rail-bolt joins straight 6010 to curved 6010B
- 1
Mark the cut point.
On the bending rail (after cure), mark exactly where the curve begins — the tangent point where the rail goes from straight to curved. This is the joint location. Mark on the straight rail the corresponding length needed to reach this point from the next newel.
- 2
Cut both rails perpendicular.
Both rails must be cut perpendicular to their respective rail axes — the straight rail cut at 90° to its length, the curved rail cut at 90° to the tangent at the cut point. On the curved rail this means using a pitch block matched to the tangent angle. The cuts should meet flat.
- 3
Drill the rail-bolt pilot.
Center the rail-bolt hole on the joining faces. On a curved rail, the centerline at the joint may be slightly offset from the tangent — measure and drill from the rail centerline, not the axis. Otherwise the bolt comes through the side.
- 4
Dry-fit, glue, torque.
Standard rail-bolt sequence: thread the stud into the straight rail tee-nut, slide the curved rail onto the stud, glue both faces, work nut and washer through the access mortise, torque. Clean glue squeeze before set.
- 5
Blend the joint visually.
Sand the joint with 180 then 220 grit, light strokes along the rail axis on both sides simultaneously. The joint becomes invisible. Test by running a finger across the seam with eyes closed — if you feel a step, sand more.
12 · Finishing · Sand, stain, topcoat
The curve is what people will touch
Finishing the curve.
A curved rail draws the hand. Every joint, every kerf line, every glue residue is going to be felt by every user. Finishing the curve takes more time than finishing a straight rail of the same length — every section has its own grain orientation, and curved surfaces don't sand straight. The good news: the most demanding part is the underside, which most people won't see.
- 1
Wait full cure.
Do not start finishing until 48 hours after clamp release on PVA, 72 hours on PU. Glue continues to cure for days; stain applied to partially cured glue lines will not match the surrounding wood.
- 2
Scrape and sand the underside.
Scrape glue residue with a sharp chisel. Sand the underside 80 → 120 → 180 with a sponge that follows the curve. Dust off, wipe with mineral spirits to check for residual glue (it appears as a lighter spot under spirits).
- 3
Sand the top.
Sand the top face 120 → 180 → 220 along the rail axis. The crown of the rail wants a curved sanding tool — a rubber block with a slight relief, or a sanding sponge. Avoid sanding the rail edges flat — keep the original profile.
- 4
Stain.
On red oak, white oak, or maple bending rail, test stain on a kerf-line scrap before committing. End grain (at the rail joints) takes stain heavier than face grain — pre-condition end grain or wipe stain off the joints faster than the rest of the rail.
- 5
Topcoat and wax.
2–3 coats of polyurethane (sanded between with 320). Allow full cure (24 hr) before traffic. For premium runs, finish with paste wax over the cured topcoat — buff with a soft cloth. The wax fills any remaining kerf-line micro-texture.
13 · Alt method · Shop-laminated
When site-bending will not take it
Order it laminated.
Where the radius is tighter than R = 12", where the curve is compound (changes direction along its length), or where the species is too brittle to bend (think hard maple, ipé, exotic hardwoods), site-bending stops being a method. The UWP shop laminates the curve from multiple thin plies (each ply individually flexible) glued and clamped to a curved form. The result is a finished arc delivered to the jobsite, ready to mount.
14 · Troubleshooting · Field problems
Things that go wrong on real jobs
Field troubleshooting.
15 · Sign-off · Code-compliance checklist
Curve does not change code
Final inspection.
A curved handrail meets the same IRC code as a straight one — there is no exemption for curves. Height is still 34"–38" plumb above the nosing; graspability is still Type I or Type II; continuity is still end-to-end of the flight; returns at the wall side still apply. The checklist below mirrors the straight-rail sign-off with the curve-specific adds.
- Handrail height 34"–38" plumb above nosing along the full curve and the straight sections (R311.7.8.1)
- Handrail continuous from top to bottom riser line, no breaks at the curve transition (R311.7.8.2)
- Handrail grasp meets Type I or Type II at every point along the curve (R311.7.8.3)
- Handrail terminates in newel or returns to wall via rosette (R311.7.8.4)
- 1-1/2" minimum clearance between handrail and wall, including along the curve
- Stair guard ≥ 36" measured from tread nosing (R312.1.2)
- 4" sphere cannot pass between curve balusters — radial geometry tightens spacing on the inside of a curve, check at the tightest point
- Newel anchors at curve termination resist 200-lb concentrated load (R301.5)
- Bending rail kerfs all closed and glue lines fully cured (24 hr+)
- Sub-rail (if used) fully fastened to substrate at ≤ 8" spacing
- Glue squeeze visible at every kerf during clamp-up (verified before clean-off)
- No visible kink, flat, or out-of-curve point along the radius
- Transition joint to straight rail flush — no step felt by hand
- All rail-bolt access mortises plugged with matching species
- Underside scraped of glue residue, sanded to blend with face
- Top face sanded along axis, no cross-grain marks
- Stain or finish color matches straight sections within hand-eye tolerance

