Skip to main content
Unique Wood Products

Custom Retro-Fit Landing Platform

Renovation overlay for a stair landing — the retro-fit profile scaled up for L- and U-turn landings.

  • Instant estimate
  • ANSI A shop drawing
  • DXF for CAD
Where it goes & how to measure ↓
Loading configurator…
Where a retro-fit landing goes

Re-deck the landing
without tearing it out.

The landing version of the retro-fit tread: a 5/8" solid hardwood overlay sized to the existing platform, with a built-up 1" bullnose that wraps the edge the lower run meets.

  1. Trim the old nose flush

    Cut the existing edge back square to the riser below it, the same as a retro-fit tread.

  2. Measure the existing landing

    Width skirt to skirt, depth from the back wall to the trimmed front edge. The overlay adds 1-1/4" of nose; stocked at 48" × 48", larger and L / U shapes to template.

  3. Same lip, bigger board

    The body sits flat on the old deck and the lip drops over the edge. Pair it with 8071 / 8073 retro-fit treads to re-do the whole stair in one pass.

  4. Open side? Return the end

    On an open side the overlay runs 1-1/4" past the stringer and a mitered returned end wraps the nose around the edge. Handed — specify left or right.

How a retro-fit landing platform re-decks an existing landingPlan of an L-shaped stair with the landing platform highlighted as an overlay on the existing landing. Below it, a section through the landing edge: the old nose trimmed flush, a 5/8 inch hardwood body on the old deck, and a built-up 1 inch nose wrapping the edge.PLAN · L-SHAPE LANDINGThe overlay re-decks the platform the lower run meets.48" × 48"overlay on the old landingnewelnoseon the edge thelower run meetsUPDrawn to scale · 48"-wide stair · 48" × 48" landing · 11-1/2" treads either sideSECTION · OVERLAY AT THE LANDING EDGEOld nose trimmed flush; 5/8" body on the deck, 1" bullnose caps the edge.11-1/2" overlayexisting 10-1/4" + 1-1/4" nose1"nose1-1/4" nose lip5/8"bodyriserexisting treadold nosetrimmed flushDrawn to scale · existing 1" deck, nose trimmed flush · 5/8" body · 1-1/4" nose runTHE MITERED RETURNED END · OPEN STAIRCASEOne side of the stair meets a wall; the other is open, so that end shows.The mitered returned end wraps the nose round the open end so no raw board end shows.1 · FROM ABOVEWALL SIDEclosed endcut square,butts the skirtBACKsits against the riser — the upright board of the step aboveFRONT · THE NOSEthe rounded edge you step overoutside face of the stringer(the board the treads sit on)1-1/4"OPEN SIDEno wall — you can seethis end of every stepmitered returned enda 1-1/4" piece with the samenose, fixed to the end so thenose turns the corner andthe raw board end is hidden.It runs 1-1/4" past the back,behind the riser above.2 · STANDING BESIDE THE OPEN SIDEThe same tread seen from the room, looking at its open end.FRONT · THE NOSE← the tread carries on to the wall sideBACK · against the riserOPEN SIDEthe mitered returned endthe same nose, wrappedround the corner — no rawend of the board showingMeasure: wall to the outside face of the open stringer, plus the 1-1/4" returned end.Not reversible: it has a top and a bottom — tell us which side is open.In the configurator: tick Left or Right return under Nosing & Returns.
Top: an L-shaped stair in plan with the overlay on the existing landing. Middle: section through the landing edge — old nose trimmed flush, 5/8" body on the deck, 1" nose wrapping the edge. Bottom: the returned end where a side is open.
UWP hardwood tread profiles stacked in-house, showing their grain and return details.

Crafted in-house · NW Houston / Tanner Rd

Custom stair work, up close.

Explore photographs of UWP treads, curved details, and custom fabrication.

See our stair work
Choosing your species

Match the floor and the stair disappears.

A staircase reads best when the treads match the floor they meet. Species is chosen for tone, not just hardness — pick the one closest to your flooring and the stair disappears into the room instead of fighting it.

Images simulate a water-clear matte coat to show natural species color. UWP material ships unfinished; tone and figure vary by board.

Representative Red Oak wood grain under a clear matte finish

Red Oak

Core catalog
Janka Hardness1,290 lbf

Pairs with — Medium-tone floors with a warm, slightly pink-red cast — the default for red oak flooring in most American homes.

Representative White Oak wood grain under a clear matte finish

White Oak

Core catalog
Janka Hardness1,350 lbf

Pairs with — Lighter, cooler floors — white oak, natural, wire-brushed, and modern light finishes. Reads warm-tan, not pink.

Representative Hard Maple wood grain under a clear matte finish

Hard Maple

Made to order
Janka Hardness1,450 lbf

Pairs with — Pale, clean, contemporary floors where an even, near-white tone is wanted.

Representative Hickory wood grain under a clear matte finish

Hickory

Made to order
Janka Hardness1,820 lbf

Pairs with — Rustic and character-grade floors with high light-to-dark contrast.

Representative Walnut wood grain under a clear matte finish

Walnut

Made to order
Janka Hardness1,010 lbf

Pairs with — Dark, rich floors and high-end interiors where a deep chocolate tone is the statement.

Not sure which to match?

Send a sample of your floor — we'll species-match the run.

Specifications

The full spec sheet. For the builder who scrolled this far.

Body1" solid or 5/8" retro-fit
Edge profilesBullnose · eased · mitered returned ends
ConstructionEdge-glued solid — never veneered
SpeciesFive configured hardwoods
DimensionsAny width, depth & length to spec
GeometrySquare, pie, winder, curved, landing
MilledIn-house in Houston, TX
SurfaceUnfinished, sanded
Lead timeConfirmed at quote
Minimum order1 piece
TemplatingOn-site for curved & complex
QuotePlanning estimate in the configurator
Popular wood species

The species we run most.

Red Oak and White Oak are core catalog species; the rest are made to order. Current material availability is confirmed on the quote. Janka hardness is listed for reference—every species here is solid, edge-glued, and refinishable.

Red Oak
Core catalog
Hardness
1290 lbf
Color & appearance
Light-to-medium brown with a reddish cast; stains slightly pink.
Grain & texture
Bold, prominent grain lines with occasional swirl.
White Oak
Core catalog
Hardness
1350 lbf
Color & appearance
Light-to-medium brown with an olive, not pink, cast.
Grain & texture
Medium-to-coarse, slightly open structure.
Hard Maple
Made to order
Hardness
1450 lbf
Color & appearance
Creamy white to light reddish-brown; clean and modern.
Grain & texture
Mostly straight, sometimes wavy; fine, even texture.
Hickory
Made to order
Hardness
1820 lbf
Color & appearance
Creamy lights against rich browns; rustic and striking.
Grain & texture
Coarse, pronounced, high-contrast figure.
Walnut
Made to order
Hardness
1010 lbf
Color & appearance
Deep, luxurious chocolate tones; warm and refined.
Grain & texture
Fine-to-medium grain, smooth and elegant.

These are the species that match or complement common hardwood flooring. Running the stair in the same species as the floor keeps grain and tone consistent, so the staircase reads as a deliberate extension of the room rather than a separate part.

Want the full picture — Janka hardness, tone, grain, and the species we source to order? Read the complete wood species guide →

Why solid hardwood

Built to outlive the renovation.

No engineered cores, no veneer, no compromises — the reasons a solid UWP tread is still there decades after the trends move on.

  • Solid, never veneered

    Full-thickness hardwood the whole way through — not a veneer skin over a cheap core. What you sand into is more of the same wood.

  • Refinishable for decades

    Sand and recoat it many times over its life. A solid tread outlasts the carpet, the paint, and usually the renovation that put it in.

  • North American hardwood

    North American hardwood, milled in-house for a short supply chain and a solid-wood result without imported-veneer surprises.

  • Warm & quiet underfoot

    Solid wood absorbs footfall and holds room temperature — none of the cold, hollow click of tile, stone, or hollow-core treads.

Frequently asked

What builders actually ask.

Straight answers to the questions we field at the will-call counter — not a marketing FAQ.

Can I overlay an existing landing?
Yes — this is the retro-fit profile scaled up to a landing. It caps the existing landing the way a retro-fit tread caps a step: a full 1″ nose on the open edges over a thinner body across the field, so the landing gains a solid hardwood surface without the height jump a full 1″ panel would create.
How does it meet the retro-fit treads on the flight?
Order them together and specify the same body thickness. The whole point of a retro-fit system is that every walking surface rises by the same amount, so the riser heights stay consistent through the turn. Mixing a retro-fit landing with full-thickness treads, or the reverse, puts a step where the stair does not want one.
What about the transition to the floor at the top?
That edge is where retro-fit jobs get untidy. The landing surface is now higher than the adjoining floor by the body thickness, so the junction needs either a transition piece or a plan to bring the floor up to meet it. Decide which before ordering, and include that edge in the measurements.
Does the existing landing have to be flat?
Yes, and more so than a tread does, because the span is bigger and a hump in the middle shows. Strip it to the substrate, pull every staple, remove the existing nosing so the new panel bears flat to its front edge, and fix any deflection or squeak in the framing first. A large panel telegraphs everything underneath it.
Can I do the landing and the treads in stages?
You can install in stages, but order in one go. The species, the profile and the body thickness have to match across the whole stair, and material ordered weeks apart comes from different stock and will not match in tone on a stain-grade job. Order the full stair, install it in whatever sequence suits the site.
All answers →

Terms used on this page