Skip to main content
Unique Wood Products

T-moulding, reducer, threshold or saddle — which floor transition do I need?

Two floors at the same height that both float take a T-moulding. A thicker floor stepping down to a thinner one takes an overlap reducer. A floor ending at a doorway or a different material takes a threshold. Two fixed floors at the same height take a saddle. On an accessible route the drop, not the name, decides.

The short version

  • Same height, both floating — T-moulding. The centre tongue sits in the gap so both floors can still move.
  • Step down to a thinner floor — overlap reducer. The lip rides on the thicker floor and hides its cut edge.
  • Ends at a doorway or another material — threshold. It covers the raw edge where the floor simply stops.
  • Same height, both fixed down — saddle. Solid underneath with a shallow channel, so nothing is left to move.
  • On an accessible route — the height change decides, not the profile name: 1/4″ vertical, 1/4″–1/2″ beveled at 1:2, anything more is a ramp.

The full answer

Every transition answers the same two questions: are the two floors the same height, and is either of them floating? Get those right and the profile picks itself. Get them wrong and the joint either traps a floating floor so it buckles, or leaves a lip that catches a toe.

Same height, both floors floating — T-moulding

A T-moulding is a T in section: the stem drops into the gap between the two floors and the head laps over both. Nothing fastens to the floors, only to the subfloor through the gap, so both floors keep their expansion space. That is the whole reason it exists — a floating floor that is pinned at a doorway has nowhere to go when the slab gives up its summer moisture.

  • Use it between two floating floors of the same thickness — laminate to laminate, SPC to SPC, or across a wide doorway in one continuous floor.
  • Leave the gap. The stem needs room on both sides; a T-mould glued tight to both edges is a fastened floor with extra steps.
  • Stocked as UW9896, with UW9895 as the mini version for narrower gaps.

A thicker floor stepping down — overlap reducer

An overlap reducer has a lip on the high side and a ramp down to the low side. The lip rides on the finished floor and covers its cut edge; the body fastens to the subfloor only, so a floating floor underneath still moves. Match the drop to the floor being reduced — the clearance under the lip equals the nominal floor thickness, so a 3/4″ solid floor wants a 3/4″ drop and a 1/2″ engineered floor wants a 1/2″ one.

  • Use it where hardwood meets tile, vinyl or a bare slab at a lower level.
  • UW9897 is the domed 1-3/4″ profile; UW9893 is the mini.
  • UW9894 and UW9890 (Low-Slope Overlap Reducer) are the wider 2″ profiles with a straight 1-1/4″ ramp running down to a 1/8″ toe — a longer, more even slope underfoot. Not for an accessible route: see below.

A floor that simply ends — threshold

A threshold covers the raw edge where a floor stops: at an exterior door, at a sliding track, or where carpet takes over. It is the least fussy of the family and the one most often used where nothing else quite fits. Stocked as UW9892, with UW9891 as the baby threshold for a shallower edge.

Two fixed floors at the same height — saddle

A saddle is solid underneath with a shallow channel rather than a tongue. Because it is solid it cannot accommodate movement, which is exactly right when both floors are nailed or glued down and neither of them is going anywhere. Stocked as UW9898, with UW9899 as the mini.

On an accessible route, the height decides

Commercially — and in any residential project that chooses to follow it — a transition on an accessible route is a change in level, and the rule is about height rather than profile: up to 1/4″ may be vertical; 1/4″ to 1/2″ must be beveled no steeper than 1:2; more than 1/2″ has to be a ramp at no more than 1:12. Height is measured to the top of the transition, and an overlap reducer’s lip rides on the higher floor — so every lipped reducer stands its full thickness above the lower floor, 3/4″ for UW9894 and 1″ for UW9890, and neither belongs on an accessible route. The answer there is a flush bevel reducer: no lip, its top flush with the higher floor, so the only change in level is the one between the floors. UW9901, UW9902 and UW9903 cover a 1/4″, 3/8″ and 1/2″ difference and comply; UW9904 (3/4″) does not, because nothing over 1/2″ can be a bevel. The architect of record signs off either way.

The whole family at a glance

What the two floors are doingProfileStocked as
Same height, both floatingT-mouldingUW9896 · UW9895 mini
Thicker floor stepping down to thinnerOverlap reducerUW9897 · UW9893 mini
Step down on an accessible route (1/2″ max)Flush bevel reducerUW9901 · UW9902 · UW9903
Floor ends at a door or another materialThresholdUW9892 · UW9891 baby
Same height, both fastened downSaddleUW9898 · UW9899 mini
Floor meets the edge of a stairStair nosingSee the stair mouldings

Related products at UWP

Related questions

Terms on this page

Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.

Ask the Houston team

Published 2026-09-17