1 · Foreword · Two systems, one guide
Two distinct installs
Turned dowels or plowed rail.
Wood balusters fall cleanly into two install systems with no overlap. Turned balusters have preformed round dowel pins at top and bottom — they drop into mortise holes drilled in the tread and the handrail underside. Square balusters have no dowels — they ride in a square channel routed into the underside of a plowed handrail, locked in by fillet pieces between each baluster. Pick the system first, then follow the install path for that system.
2 · Anatomy · How each system works
Different rails, different installs
Two systems side by side.
Figure in the PDF: TURNED SYSTEM · preformed dowel into drilled mortise
Figure in the PDF: SQUARE SYSTEM · square baluster in plowed rail, fillet between
3 · Inventory · Turned wood balusters
The lathe-turned program
Turned baluster inventory.
Turned balusters are lathe-cut to a fixed profile — typically a colonial, traditional, or transitional silhouette with a turned ball, vase, or pin-top detail. Most balusters in the 5xxx family have preformed dowel pins at top and bottom; some pin-top variants need the top dowel cut to length on-site. Stock is usually red oak; specify WO at order for white oak.
- UW-5015
- Colonial turned baluster, oak
- 34" / 36" / 39" / 42"
- UW-PR5015
- Colonial turned, primed
- 34" – 43"
- UW-5342
- Turned, 1-3/4" base, oak
- 42"
- UW-PR5067
- Turned, primed
- 34" – 41"
- UW-PR5141
- Turned, primed
- 34" – 41"
- UW-P5315
- Turned, poplar
- 34" – 42"
- UW-PR5005
- Turned, primed
- 36" / 42"
- UW-PR5090
- Turned, primed
- 36" / 42"
- UW-PR5241
- Turned, primed
- 41"
Lengths vary by profile — most balusters come in 31", 34", 36", 39", 41", or 43" depending on the family. Verify length needed (rail height + rail thickness ÷ 2 + tread depth + safety margin) before ordering.
4 · Inventory · Square balusters + fillet
The square wood program
Square balusters and fillet.
Square balusters are dimensional stock — 1", 1-1/4" or 1-3/4" square — milled long and cut to fit on-site. They ride in a plowed handrail (UW-6010P, 6210P) and lock in place with fillet pieces between each baluster. The fillet is what sets the spacing and finishes the underside of the rail.
- UW-5060
- 1-1/4" sq. oak baluster
- 42" · primed 36" / 41"
- UW-5360
- 1-3/4" sq. oak baluster
- 42" · primed 36" / 42"
- UW-PR5160
- 1" sq. primed baluster
- 36" / 42"
Match the plow width to the baluster:
- 1-1/4" sq. baluster: 1-1/4" plow (UW-6010P standard)
- 1-3/4" sq. baluster: 1-3/4" plow (special order)
Fillet is milled to the plow width in the rail species and quoted with the handrail.
Each baluster needs one fillet on each side at the rail (two fillets per baluster) plus matching fillets in the tread plow if the tread is also plowed.
Order linear-feet of fillet = number of balusters × 2 × open distance between balusters, plus ~15% for cut waste and trim.
Fillet shows in the finished assembly — order the same species as the handrail and balusters for an even stain.
5 · IRC Code · Spacing & sphere
Quick code reference
The 4" sphere sets the spacing.
Wood balusters carry the same IRC code that applies to all guard systems — height, sphere rule, and load. The active constraint on a baluster install is the 4" sphere rule: nothing between balusters that lets a 4" ball through. Spacing math comes from this rule. Handrail height (R311.7.8.1) and guard load (R301.5) are handled by the rail and newel install — see the UWP Handrail & Newel Installation Guide for those rules.
Figure in the PDF: R312.1.3 — 4" SPHERE RULE · SPACING MATH
6 · Tools · Materials · Adhesives
Different tools for each system
Tools & materials.
- 5/8" and 3/4" Forstner bits — round mortises in tread and rail
- Self-centering drill jig — keeps mortise hole on baluster centerline
- Drill press OR cordless drill with bit guide
- Depth-stop on the bit (~1" deep mortise — never blow through)
- Combination square — set bit perpendicular to the rake
- Pitch block (from the Handrail & Newel guide) — for cut angles
- Compound miter saw — top-cut on pin-top balusters
- Block plane for fine dowel-fit adjustment
- Pin nailer (23 ga) — fillet tacks; almost no visible hole
- Coping saw or small handsaw — fillet trim at the baluster face
- Sharp 3/4" chisel — clean plow corners, trim fillet ends
- Combination square — fillet length transfer
- Pencil + masking tape — fillet length marks
- Wood glue (Titebond III or II) — main bonding agent, both systems
- Polyurethane glue — gap-filling option for loose-fit mortises
- Construction adhesive — for fillet beads in the plow (sub to wood glue, not above)
Iron balusters use epoxy for steel-to-wood bond. Wood balusters use wood glue — PVA wets the wood fibers and creates a chemical bond that's actually stronger than the wood itself. Epoxy on wood is overkill, doesn't penetrate, and looks worse if it shows.
- 15-ga finish nails — for toe-nailing square balusters at tread (if no tread plow)
- 23-ga pin nails — fillet tacks, position-only
- Wood screws #6 × 1-1/4" — alternative to toe-nails at tread for square
- Color-matched putty stick for nail hole touch-up
7 · Layout · Spacing math
Two distances per run
Spacing — and the rake catch.
On a level guard (landing, balcony, level run between newels), 4-1/8" center-to-center spacing with a 1-1/4" baluster gives 2-7/8" open — well under the 4" sphere. On a stair rake, the same 4-1/8" centers measured horizontally creates a diagonal opening larger than 4" — the sphere passes between two balusters at the slope angle. Tighten the centers on the rake to keep the diagonal gap under 4".
Figure in the PDF: LEVEL RUN — straightforward math
Figure in the PDF: STAIR RAKE — diagonal opens up
- 1
Compute the level spacing.
Open space + baluster width = center spacing. For 1-1/4" baluster, target 2-7/8" open → 4-1/8" centers. Walks under code.
- 2
Compute the rake spacing.
Multiply level spacing by cos(stair angle). For a 7-3/4" / 10" stair, angle = atan(7.75/10) = 37.8°. cos(37.8°) ≈ 0.79. So 4-1/8" level → ~3-1/4" on rake. Round to a clean construction number.
- 3
Per-run divide for the layout.
On the level run: (length between newels − baluster width) ÷ center spacing, rounded UP to a whole number. Recompute spacing with the rounded count. On the rake: (sloped length between newels − baluster width) ÷ rake center spacing, rounded UP.
- 4
Verify with a sphere.
Lay out one baluster pair to the computed spacing; test with a 4" hole saw test plug or a printed 4" circle. If it passes between, tighten centers by 1/8" and recompute the run total.
8 · Layout · Tread-level placement
Two per tread, almost always
Tread-level placement.
On a standard residential stair, the layout is two balusters per tread — one near the front (about 1/3 of the way back from the bullnose) and one near the back. The center-to-center distance follows the rake math from page 8. Treads with closer baluster spacing (three per tread) are sometimes specified for thinner balusters or a tighter aesthetic; verify against the sphere rule at order.
Figure in the PDF: STANDARD LAYOUT — TWO BALUSTERS PER TREAD
- 1
Mark from the front nosing.
Measure from the front edge of the tread back to the position for Baluster 1 — typically 1/3 of the tread depth from the front. For a 10" tread, that's ~3" from the nosing. Mark with a pencil dot on the tread surface, centered side-to-side on the tread's open edge.
- 2
Compute Baluster 2 position.
Baluster 2 is at Baluster 1 position + rake center spacing (e.g., 3-1/4"). For the standard 10" tread, that places Baluster 2 about 6-1/4" from the front nosing — roughly 2/3 of the way back. Mark identically.
- 3
Repeat on every tread.
Use the same offsets on every tread. The handrail rake plus the consistent tread-level placement creates the pleasing visual rhythm of evenly-spaced balusters running up the stair.
- 4
Mark the rail underside.
Plumb up from each tread mark to the underside of the handrail. Mark each plumb point with a pencil dot. These become the mortise centers for turned balusters or the fillet positions for square balusters.
9 · Install · Turned baluster method
Drill, dry-fit, glue
Turned baluster install.
Turned balusters install in a fixed sequence: drill the tread mortises first, drill matching handrail mortises (plumb to the tread marks), dry-fit every baluster to verify length, then glue and set. The mortises do the structural work — get the depth and the alignment right and the install holds for decades.
- 1
Drill tread mortises.
At each marked baluster position, drill a 5/8" or 3/4" diameter mortise (match the dowel pin diameter — typically 3/4" for standard turned balusters) ~7/8" deep into the tread. Use a Forstner bit with a depth stop. Drill perpendicular to the tread surface, not plumb to ground. Clean the hole of chips with compressed air.
- 2
Drill handrail mortises.
Plumb up from each tread mortise to mark the rail underside. Drill a 5/8" mortise ~1" deep into the rail underside. Drill perpendicular to the handrail axis (NOT plumb to ground — perpendicular to the rake) using a self-centering jig or a square-aligned bit. The handrail mortise should be slightly oversize compared to the top pin to allow dry-fit adjustment.
- 3
Dry-fit every baluster.
Set each baluster bottom dowel into its tread mortise, then guide the top dowel into the rail mortise. The baluster should drop in cleanly to about 1/8" of full seat — that 1/8" is your glue allowance. Check plumb in both directions (front-back and side-side). For pin-top balusters, mark the top dowel where it meets the rail mortise mouth — that's your cut line; cut on the bench, dry-fit again.
- 4
Glue and set.
Pull each baluster out one at a time. Apply slow-set wood glue (Titebond III preferred) inside both mortises — a generous bead, not just a dab. Reset the baluster: bottom dowel into tread mortise first, then top dowel into rail mortise. Wipe glue squeeze with a damp rag immediately. Verify plumb one last time. The baluster should feel snug; if it rocks, the mortise is oversized — switch to PU glue for foam-fill or shim with a slim wedge.
- 5
Cure and clean.
Leave undisturbed for 24 hr minimum. The glue cures fastest where it's squeezed thinnest, slowest where the dowel meets the mortise bottom. After cure, run a finger over every mortise mouth to check for residual glue ridges; sand any high spots with 220 grit.
10 · Install · Square baluster method
Cut, fit, fillet
Square baluster install.
Square balusters install in the opposite order from turned: start by setting all balusters dry into the plowed rail and tread, verify spacing, then cut and install fillet pieces to lock the spacing and finish the underside. The fillet does the structural work of holding the spacing — get the fillet cuts right and the balusters can never shift.
- 1
Cut baluster length.
For each baluster: measure from the floor of the tread plow (or the tread top if no tread plow) up to the floor of the handrail plow. The baluster cut length equals this distance minus 1/16" for a snug fit. The bottom cut is square (perpendicular to baluster axis); the top cut matches the rake angle (use the pitch block on the miter saw fence). Cut all balusters at once for consistent length.
- 2
Dry-set all balusters.
Drop each baluster into position — bottom into the tread plow at the marked position, top into the handrail plow. The baluster should be tight in the plow with no wobble side-to-side. Verify plumb in both directions. Adjust the rail plumb-marks if any baluster is leaning. Do this for all balusters in the run before any fillet goes in.
- 3
Toe-nail or fasten bottoms.
For each baluster, drive one 15-ga finish nail at a 45° angle through the back face of the baluster into the tread, or use a #6 × 1-1/4" wood screw if the tread plow is exposed and you'll cover with fillet. Pre-drill if the species is splitty (red oak does; poplar doesn't). The bottom is now anchored.
- 4
Cut and install fillet — bottom (tread plow).
Measure the open space between two adjacent baluster bottoms (face-to-face). Cut a fillet piece to that exact length — square cuts both ends. Apply a thin bead of wood glue in the tread plow, drop the fillet into the plow, tap snug between balusters. Pin-nail with one 23-ga pin nail through the fillet centerline into the tread. Repeat for every gap.
- 5
Cut and install fillet — top (handrail plow).
Measure the open space at the handrail (which differs from the tread space because of the rake angle on the rail). For each top fillet, the cut length matches the open space at the rail level. Apply glue to the plow, drop fillet in, pin-nail. Be especially careful with finish here — the top fillet is the most visible piece in the assembly.
11 · Detail · Fillet method
The piece that does the work
Fillet detail.
The fillet — a thin strip of wood matching the plow width — is what makes the square-baluster system work. Each fillet piece sits in the plow between two balusters, glued and pin-nailed. It locks the baluster spacing structurally and finishes the rail underside visually. Every gap between balusters gets a fillet at the rail; matching fillets in the tread plow if applicable.
Figure in the PDF: PLOW + FILLET — RAIL UNDERSIDE ELEVATION
12 · Cuts · Pitch & angles
The pitch block does the angles
Cuts and angles.
Baluster cuts depend on the system. Turned balusters with fixed-length top dowels need only a square cut on the bottom dowel (if it ships long). Pin-top turned balusters get the top dowel cut square to the dowel axis (not the rail rake — square). Square balusters need a top cut matching the rail rake on the rake-run and a square cut on level runs. Same pitch block as the handrail install (from the UWP Handrail & Newel guide).
Figure in the PDF: PITCH BLOCK ON MITER SAW FENCE · baluster top matches rail rake
- 1
Set the pitch block.
Make a pitch block from 2x scrap as in the Handrail & Newel Installation Guide — the rise (riser height) as the short leg and the run (tread depth) as the long leg. The hypotenuse is the rake angle. Place the block on the miter saw fence: long leg flat against the fence, short leg horizontal.
- 2
Turned bottom — square cut.
If the bottom dowel ships at full length, no cut needed — drop into mortise. If the bottom dowel needs shortening for a specific tread depth, cut perpendicular to the dowel axis (square cut, no pitch block). The dowel doesn't care what angle is below it — only the depth of seating matters.
- 3
Pin-top turned — square cut of top dowel.
Pin-top variants ship with an oversize top dowel. Mark the dowel where it exits the rail mortise mouth at final dry-fit position, subtract the desired seat depth, cut square (perpendicular to dowel axis) on the miter saw. Re-fit and adjust if needed.
- 4
Square baluster top — pitch-block cut.
For square balusters on a stair rake, the top cut matches the rail underside angle, which is the pitch. Place the baluster top-up against the miter saw fence with the pitch block beside it; cut along the pitch block hypotenuse line. The baluster top now fits cleanly into the plow.
- 5
Square baluster bottom — square cut.
Bottom cut is always square — perpendicular to the baluster axis. The baluster sits plumb (vertical) so the bottom needs to rest flat in the tread plow. No pitch-block angle here.
13 · Finishing · Pre-finish strongly preferred
You will not reach in there later
Pre-finish before install.
A baluster run has 20+ balusters spaced 3 inches apart. No paint brush, no rag, no sanding sponge reaches between them once the run is installed. The only way to deliver a clean finished baluster run is to finish every piece before it goes up. Touch-up after install is for nail holes and joint plugs only — the main finish is set on saw horses.
- 1
Touch-up nail holes.
Pin nail holes (23 ga) are essentially invisible — no fill needed for most stain colors. For deeper toe-nail or screw holes at baluster bottoms, fill with color-matched putty stick after install. Wipe excess with a clean rag while still soft.
- 2
Address dowel-mortise residue.
After turned-baluster install, glue squeezes around the mortise mouth on both ends. Scrape with a sharp chisel held at high angle, sand the mortise mouth area with 220, blend with a touch of stain.
- 3
Top fillet check.
On square-baluster runs, the top fillet is the most-seen finish. Sight-check from across the room under daylight — any reflection mismatch, pin nail showing, or glue residue gets touched up here.
- 4
Final wax.
For premium installs, a clear wax over the cured topcoat — applied with a soft brush between balusters, buffed lightly with a soft cloth. Gives the run the same hand-feel as the handrail.
14 · Sign-off · Checklist + troubleshooting
Before the AHJ walks the job
Final inspection.
- 4" sphere cannot pass between any two adjacent balusters (R312.1.3) — checked at the tightest layout point
- 6" sphere cannot pass at the triangular space at the bottom of the guard
- Stair guard height ≥ 34" from the nosings at every step (R312.1.2 — set by rail)
- Every turned baluster fully seated — no dowel visible at mortise mouth
- Every square baluster plumb (no lean)
- Every fillet glued and pin-nailed — no rattle when tapped
- All glue squeeze cleaned at mortise mouths
- Nail holes filled with color-matched putty
- No raw wood visible — pre-finish complete
- No sphere-test plug fits between any baluster pair

