TEC VersaPatch
327 · Latex Modified Floor PatchFast-Set · Zero VOC

Patch the floor. Install in 30 minutes.
VersaPatch is TEC's fast-setting, latex-modified, cement-based floor patch for voids and irregularities in wood, concrete, and most existing floor materials. Patches ½″ down to a feather edge in one pull. Flooring goes back over the patch in 30–45 minutes — fast enough to keep a same-day install on schedule. Zero VOC, LEED- compliant, MAS Certified Green®. 25 lb bags stocked at NW Houston / Tanner Rd.
- ·Feather edge to ½″ (12 mm)
- ·Install flooring in 30–45 min
- ·Non-shrinking · smooth finish
- ·Zero VOC · LEED-compliant
Built for same-day floor work.
Fast-setting latex-modified cement — patch in the morning, install sheetgoods, resilient tile, carpet, wood, or ceramic over it the same hour.
Patch voids and irregularities from a true feather edge up to ½″ (12 mm) in one application. Non-shrinking — no callbacks for telegraphed seams.
Bonds to existing concrete, terrazzo, masonry, ceramic, plywood, well-bonded resilient flooring, adhesive residue, and gypsum — interior, fast, and trowel-easy.
Technical data.
Specifications per the current TEC VersaPatch 327 technical data sheet. Always refer to the current TDS and SDS before installation.
What it goes over.
- ·Existing concrete
- ·Concrete terrazzo
- ·Epoxy terrazzo
- ·Cement backerboard
- ·Tile (existing, well-bonded)
- ·Masonry
- ·Exterior-grade plywood
- ·Exterior-grade Lauan plywood
- ·Well-bonded resilient flooring
- ·Adhesive residue
- ·Gypsum substrates
What goes on top.
- ·Sheetgoods (vinyl)
- ·Resilient tile · LVT / LVP
- ·Carpet
- ·Wood flooring (glue-down)
- ·Ceramic tile
- ·Stone tile
Verify the substrate is structurally sound, clean, dry, and free of contaminants that could break the bond. Mix per the current VersaPatch TDS — too much water reduces strength and slows set. Patches over ½″ (12 mm) thick require multiple lifts; follow the TDS for the technique.
VersaPatch by the 25 lb bag — pulled at the Tanner Rd yard.
Questions people ask about the floor going over this
How do I install SPC flooring?
SPC installs as a click-lock floating floor over almost any substrate. The sequence: confirm the subfloor is flat (within 3/16″ over 10 feet), acclimate the planks 48 hours, lay an underlayment if needed, click planks together starting at the longest wall, leave a 1/4″ expansion gap at every wall and obstruction, finish with baseboard or quarter round. Most rooms install in a weekend.
Read the answer →Click-lock vs. glue-down flooring — which installation method should I choose?
Click-lock floats over the subfloor with no adhesive — fast to install, easy to remove for repair, but slightly hollow underfoot. Glue-down bonds the floor directly to the subfloor — feels more solid, transmits less sound, lasts longer, but is far harder to repair or replace and requires a perfect substrate. Pick click-lock for fast residential installs; glue-down for commercial and premium residential.
Read the answer →Can I use wood flooring over radiant heat?
Yes, wood flooring works over radiant heat — but with specific rules. Engineered hardwood is strongly preferred over solid; narrower planks (5″ or less) are safer than wide planks; quarter-sawn cuts move less than plain-sawn; floor temperature must stay under 80°F at the wood surface. Install with proper acclimation and a slow heat ramp-up. Solid hardwood is possible but requires careful species selection and width discipline.
Read the answer →How do I acclimate hardwood before installing it?
Acclimate hardwood by stacking the material in the install space — not the garage, not the porch — for 5 to 7 days before installation. The room must be HVAC-conditioned at typical living temperature and humidity. The wood reaches equilibrium moisture content with the room and will not move significantly after install. Skipping this step is the #1 cause of post-install gaps, cupping, and squeaks.
Read the answer →

