Prehung or slab — which interior door should I order?
A prehung door arrives hinged in its own jamb with the lock bore already cut, and it installs into a rough opening. A slab is the door alone, for reusing a jamb that is staying. Prehung is faster and more reliable on new work or where the casing is being replaced. Slab is right when the existing jamb and casing are sound.
The short version
- Prehung — door, jamb, hinges and bore as one unit. Set it plumb, shim it, case it.
- Slab — the door only. You mortise the hinges and bore the lockset to match the existing jamb.
- New construction or new casing → prehung, almost always.
- Existing jamb and casing staying → slab, if the jamb is square and sound.
- A slab is only cheap if the jamb is good. Fighting a racked jamb costs more than the prehung would have.
The full answer
The choice is not really about the door — it is about the jamb. A prehung unit brings a new, square, factory-hung jamb with it. A slab assumes the jamb you already have is worth keeping. Everything else follows from that one judgement, so make it honestly before you price anything.
What each one asks of you
| Prehung | Slab | |
|---|---|---|
| What arrives | Door hinged in a jamb, bored | The door only |
| Opening needed | Framed rough opening | An existing jamb |
| Site work | Plumb, shim, fasten, case | Mortise hinges, bore lock, trim to fit |
| Tools | Level, shims, nailer | Router or chisels, hinge template, bore jig |
| Skill floor | Moderate and forgiving | Higher — the mortises are permanent |
| Casing | New casing both sides | Existing casing untouched |
Go prehung when
- It is new construction or a gut remodel. There is no jamb to save.
- The casing is being replaced anyway. Half the argument for a slab disappears.
- The existing jamb is out of square, racked, water-damaged or painted into a lump. A new jamb is cheaper than making a bad one work.
- The door is solid core. A heavy door wants a jamb it was hung in, shimmed correctly, with matched hinge mortises.
- You are doing many openings. Consistency across a schedule is worth far more than the per-door saving.
Go slab when
- The jamb and casing are sound and staying. A straight, square jamb with good casing is worth preserving, especially original millwork.
- You are changing one or two doors, not a house.
- The wall or the trim would be disturbed by pulling the jamb — plaster, tile returns, stone.
- You can hit the existing hinge locations. Reusing the mortises is the whole time saving; if you have to cut new ones, the advantage thins fast.
Measure before you order — either way
- For a slab: measure the existing door, not the opening. Width, height, thickness. Then measure hinge positions from the top of the door, the hinge size and whether the corners are square or radiused, and the bore height and backset — the backset is the distance from the door edge to the centre of the knob hole, commonly 2-3/8″ or 2-3/4″.
- For a prehung: measure the rough opening width and height, and the wall thickness to get the jamb depth right. A 2×4 wall with 1/2″ drywall both sides is a different jamb from a 2×6 or a furred wall.
- Check the swing direction and the hand at the opening, in person.
- Check the floor. A prehung set to a floor that is out of level will have an uneven gap at the head. Note any flooring still to be installed — the undercut depends on it.
One honest warning about slabs. A slab looks like the thrifty choice and often is, but it only stays thrifty if the jamb cooperates. If the hinge mortises do not line up, if the existing jamb is out of plumb, or if the old door was planed to fit a settled opening, you are now fitting a rectangular door into a parallelogram. That work is slow, it is skilled, and it is the reason experienced trim carpenters reach for prehung more often than homeowners expect.
UWP orders doors in rather than milling them, in both configurations, and stages them at the Houston yard for will-call. Because they are special order, the spec — size, core, hand, jamb depth, bore — is fixed when the order is placed. Confirm the measurements at the opening before submitting, and confirm the timing on the quote alongside the trim package.
Related products at UWP
Interior doors
ConfiguratorMolded panel, hollow and solid core, slab or prehung — configure the spec and submit it for a quote.
View →Moulding catalogue
CatalogCasing, door stop and back band to trim the openings once the doors are set.
View →Moulding installation guide
ProductCasing a door opening — reveals, mitres and fastening — step by step, with the PDF to download.
View →Related questions
Terms on this page
Still picking? Email us with the details — stair height, run depth, existing stair condition — and we’ll tell you what we’d actually spec.
Ask the Houston teamPublished 2026-09-14

